AmateurRadio.com

Fire up your sat tracking software, because the ISS will be live for Jamboree on The Air. An article at Southgate Amateur Radio Club’s website reports that Astronaut Mike Fossum, KF5AQG, will be participating in Jamboree on The Air from the International Space station this weekend, using the callsign NA1SS. Mike is also a scout master. 

Photo Courtesy of NASA / Southgate ARC

While he won’t be available for every pass, you may hear him from 0800-1930 UTC as this is the usual work time for the crew, but they could also stay on a little later as well. When Mike is on he will be working ITU 1, which is Europe, Africa and Russia, with the uplink of 145.200 MHz FM and ITU regions 2 & 3, which is every one else, using the uplink of 144.49 MHz. Downlown for all will be 145.800 MHz FM. Be sure to be using a wide filter if your radio supports it, as the station uses a 5 Khz FM deviation, so 25 khz channel spacing is recommended.

If you don’t have satellite tracking software installed, you can track the Space Station online at NASA’s Spaceflight website. And, AMSAT UK has a wonderful article on getting started with satellites as well. This is should a fun Jamboree this year. To all the scouts and scout masters, enjoy!

73.

Rich also writes a Tech blog and posts stories every Tuesday and Thursday on Q103, Albany’s #1 Rock Station website, as well as Amateur Radio stories every Monday thru Friday on AmiZed Studios and hosts a podcast called The Kim & Rich Show with his fiance’ Kim Dunne.

I do not spend a lot of time on VHF/UHF FM and have not for many years.  My first radio in 1993 was an Alinco DJ-580T handheld and I’ve thought at various times that a new handheld might suit me well, especially for receiving.  A few weeks ago, as I tend to, I came across a Yaesu VX-3R offered “for parts or repair” on attractive terms and so acquired it—my second handheld ever.  The problem seemed straightforward enough:  full TX power, but no RX on amateur bands.  RX on FM broadcast OK.  The seller assured me, after I had agreed to purchase based on his description, that “somebody” had told him that this problem occurs when “only one component is bad.”

Based on the seller’s description of the problem and a thorough reading of the Technical Supplement, I developed a short list of candidate failure modes, components, and sources.  Fortunately, all of the components could be sourced easily from the usual sources.

When the radio arrived, I gave it a functional check and it indeed exhibited the problem that the seller had advertised.  I quickly popped it open and noticed a small red sticker in the lower right-hand (when facing the device like you would operate it) corner of the Main Unit (Side A, per the Technical Supplement’s notation).  A neatly hand-drawn arrow pointed to component Q1025, which upon closer inspection, was clearly damaged.

So, I quickly set about identifying the component and procuring a replacement.  It was a NJU7007F3 operational amplifier.  Huh…it did not contribute to any of the failure modes I had initially suspected.  However, a careful reading of the Technical Supplement indicated that this op amp drives varactor diodes in a tracking preselector—so, if it does not work, the radio will exhibit varying degrees of deafness in the amateur bands.  I found out later that the “somebody” was actually a Yaesu technician who had seen the radio for repair at the behest of a previous owner and left the sticker for me.  At any rate, this component clearly would have to be replaced if I were to fix the radio, so I set about looking for a source.

Mouser listed it in their catalog but wanted me to buy a reel of 3000.  No thanks.  At least they had it listed.  So, I did the next most logical thing—I made a list of other parts that I needed and called Yaesu.  The part was back-ordered to Japan for 4-6 weeks, but only cost 0.42 USD.  I bought three.

After however many weeks it has been, a package from Yaesu showed up on my doorstep tonight.  After repairing a damaged PCB trace (non trivial on something this small), I was able to replace it.  The little black speck in the middle of this photograph is the removed component.  For my non-US readers, the US 0.01 USD coin (“Penny”) is about 19 mm in diameter.

The radio fired right up and received NOAA/NWS right away.  The entire repair once I had the parts was about 30 minutes.  There are still two unbuilt SoftRock kits, an IC-290A with an unlocking PLL, and W1GHZ transverters for 903 and 1296 to be worked on…maybe tomorrow…

As my son’s homeschool teacher I’m giving him plenty of writing assignments this year. Yesterday I asked him to write an essay, and I told him he could write it on anything he wanted. Here’s what he wrote:

Helping Dad Build His Antenna
by Antonio Mitchell, Tuesday, October 11, 2011

My dad has been meaning to build his antenna for his radio for a while. We (my dad and I) finally got motivated and had some free time as well to build the antenna. We began yesterday to build it. Some complications slowed us down.

Yesterday, we went to Wilmar. The first stop was Walmart. When we were in Walmart I got my glasses back. After that we began our search for parts at Menards. It took us a while to find some parts. The whole trip to Wilmar, shopping, and going home took quite a few hours. My dad had to meet with a church member. While he was gone he got a piece of metal cut for the tripod legs.

When he came home several hours later my mom and I were raking leaves. He began to put together a jig to help hold the poles together. We began to drill holes into the poles. It took both of us to do it. The bit finally broke. After supper my dad worked on making a balun. He also made a new shopping list of parts. It will be a great joy to see the antenna up on our roof.

Welcome to Handiham World.