AmateurRadio.com

Throughout the day yesterday I was getting propagation updates on my Iphone, things were not looking to good. The decision was made to work on my Elecraft K2 build and not get frustrated with poor propagation conditions. After about 20 minutes of working on the K2 I just was not getting into. Putting the project down for the evening I flipped on the K3 just to check out the band conditions. One of my handy tools for doing that is the Elecraft P3. It's great for seeing the general condition of a particular band. It seemed that 20 meters was not doing to badly considering the conditions. The first station I ran across was H70ORO from Nicaragua. His signal was rather strong considering my attic dipole does not seem to favour Central or South America. His code speed was a comfortable 20 wpm and really not much of a pileup. I made contact with only 1 watt which gave me 2,190 miles per watt contact.
The next (and final) station I contacted was EA4DRV, being pumped from my last 1 watt contact I tried working this Spanish station with 1 watt. It didn't work out as well and the contact was made eventually with 3 watts. After this contact it was time to flip the switch once again and move on to making lunches, arranging morning work clothes and all that other fun stuff.  It goes to show you that even when the propagation is in the dumpers contacts are still there to be had!
Mike Weir, VE9KK, is a regular contributor to AmateurRadio.com and writes from New Brunswick, Canada. Contact him at [email protected].

I needed to re-spool the fishing reel on my antenna launcher.

My first version used a plastic tent peg as a platform.  The sling shot was held in place by a bolt and nut going into the handle from the bottom.  This ultimately proved to be a weak point as the plastic handle of the sling shot broke over time from the stress at that point.

So when I bought new fishing line, I also bought another 8 inch corner brace.

I’ve been practicing in the park and I’ve been getting my 1 ounce fishing weight to get over branches 50 – 60 feet high with no problems.  I have discovered one thing, though.  My fishing weights (not the one in the photos) are painted bright yellow.  I think I am going to re-paint them with a very bright orange paint.  The yellow ones are a bit hard to notice when they fall onto the grass amid a bunch of dandelions!

72 de Larry W2LJ
QRP – When you care to send the very least!

Larry Makoski, W2LJ, is a regular contributor to AmateurRadio.com and writes from New Jersey, USA. Contact him at [email protected].

These may not be a surprise to you but the popular electrical CAD package, Eagle, has add ons plugins, scripts or whatever they are technically called. Most of these would probably be really useful if I ever knew what I was doing but one stands out. Its called Eagle-up.

Eagle-up takes the PCB as you’ve laid it out and puts it into the equally popular 3D CAD programme Google Sketch up. The plugin allows you to see the PCB in 3 dimensions and allows you to add components from the extensive library or draw out your own. The end result is a potential a photo realistic rendering of what you have just designed. I’m using it to place the various parts on so I can design a case to fit the MSFduino. I want to laser cut an acrylic case and Sketchup let’s you export to an svg  file by, you’ve guessed it, a plugin.

A bit of useful information to share if that’s your kind of thing.

Alex Hill, G7KSE, is a regular contributor to AmateurRadio.com and writes from Cumbria, UK. Contact him at [email protected].

Pat Tice, WA0TDA, is the manager of HANDI-HAM and a regular contributor to AmateurRadio.com. Contact him at [email protected].

As I have written I am building up my QRP and SOTA arsenal, focusing on portability, efficiency and weight. While weight and portability are obviously desirous for  your primary station configuration, I like to have some redundancy in case Plan A doesn't work. For example, I prefer resonant antenna's, but resonance in a given configuration in the backyard may not always equal resonance in the configuration you end up with in the field. So, I like antenna options.

With that in mind and a need to build something I opted for the KI6J SOTA Tuner as part of my back up antenna system. I haven't built anything in a few years and wanted to get back in the groove on melting a little solder, so I ordered the kit from Stu. Relatively speaking it is an easy kit to build. You do get the pleasure of winding a small transformer and toroid. However if that scares you as a new builder this is a great kit to learn on.

This kit is designed for use by portable QRP operations needing a lightweight, easy to deploy antenna system. Using this tuner, a portable station needs no ground radials and little or no feed line to achieve excellent results. The tuner matches the impedance of end fed, half wavelength (EFHW) wires on 40m -15m and contains a built in SWR indicator. The tuner is designed for durability and reliability of operation and handles QRP power levels, 5W CW and 10W PEP SSB.



Mike Crownover, AD5A, is a regular contributor to AmateurRadio.com and writes from Texas, USA. Contact him at [email protected].

Testing a new build of WSJTX for K1JT I hopped on to 10m and was surprised to see a strong signal. It soon revealed itself to be SM6NZV who gave me a +8dB report on my 5 watts.

This reminded me that it is May 1 today, the start of Spring and usually also the start of the Sporadic-E season. I tuned around on 6m and heard a couple of weak stations on my dipole, also a couple of stronger GMs working stations I could not hear.

I thought about installing the SDR-4+ as a panadapter for the K3 which had been one of the things I had intended to use it for. But something was amiss and I didn’t have control of the receiver’s frequency. I think the settings had got hosed, probably when I was playing around with using a USB DVB dongle as an SDR. I have no idea how to get it working again and I started getting stressed about it so I decided to abandon the idea.

SDRs are not for me, or at least not those that use a PC for a user interface. Windows is just too fragile, though if Linux is any better it’s only because there are fewer things to install on it in the first place!

Instead I will set up scanning on the K3 to scan a section of the 6m band. I always forget how to do this so I had to dig out the manual. Load the start frequency into VFO A and the end frequency in VFOB, make sure the mode and frequency are what you want and store it in a memory. I used memory 6 for 6m scanning.

To start a scan you just recall memory 6 (M>V, 6) and press and hold SCAN. I’ll probably forget that sequence of button presses as well so I looked up the CAT commands in the K3 Programmers Reference (SWT23;SWT29;SWH41;) and stored it in a KComm shortcut. I’ll probably make one for 2m as well though the chances of hearing any 2m Es up here are slim indeed. Last year I don’t think here was a single opening that extended this far north on 2m.

Julian Moss, G4ILO, is a regular contributor to AmateurRadio.com and writes from Cumbria, England. Contact him at [email protected].

The NJQRP Club is announcing the Second Annual ” Skeeter Hunt”.  The objective is to get QRPers out of their shacks for the day; and into the fresh air and sunshine, to spread their wings and fill the airwaves with “Skeeters”.  While commercial equipment can certainly utilized, bonus multipliers will be awarded for those who personally home brewed their own or kit built their own equipment (equipment not built by the operator would not count as either home brewed or kit built – it would be considered commercial equipment).  This year, the event is to be held on Sunday August 11th.  It will be a four hour sprint – from 17:00 UTC to 21:00 UTC (1:00 TO 5:00 PM EDT).

The theme for this year is “bodies of water”.  We all know that Skeeters love the water.  While we don’t want you going anywhere near actual Skeeter breeding grounds, we encourage operating near any local rivers, brooks, creeks, lakes, ponds, reservoirs, or even near a bay or the sea shore!  Please make sure to take pictures and tell us about it in your Soapbox comments. (Bird baths, swimming pools, old tires filled with water, buckets, Dixie cups, etc. will NOT count for the contest!)

Stations who wish to be designated as “Skeeters” can get a Skeeter number by requesting one by sending an e-mail to [email protected]  Please let me know if you intend to operate from a state other than your home state as listed on QRZ. Skeeter numbers will be issued from May through the day before the event. The official Website for the NJQRP Skeeter Hunt is http://www.qsl.net/w2lj/

Station Classes and Multipliers
X1 Home stations – commercial equipment
X2 Home stations – home brewed or kit built equipment
X3 Portable station – commercial equipment
X4 Portable station – home brewed or kit built equipment

Portable stations cannot use permanent antennas, i.e you can’t work from your backyard, hook up to your dipole or tower and yagi and be considered a portable station. Also, portable stations cannot be connected to the local power grid – alternative energy sources must be used – solar, battery, wind, etc.

Multi-Op Stations: – Great idea!  Want to get together with some of your best buds to have a barbeque and hunt some Skeeters?  FB deal, OM!  When you send in your log, send the calls of everyone who participated under that call and or Skeeter number.  And remember to send pictures of your group for the soapbox!

Suggested Call – Either CQ QRP or CQ BZZ

Exchange –
Skeeter Stations – RST, S/P/C, Skeeter number
Non-Skeeter Stations – RST, S/P/C, Output power

Modes – CW, SSB (new for this year!)
Power – 5W max CW, 10 Watts max SSB

Scoring –
Working a Skeeter Station – 2 points
Working a non-Skeeter Station – 1 point
Work a WAE station – 3 points  – Yes! The Worked All Europe contest (CW) is the same day – working DX stations (different continent) will get you extra points!

Total score equals the number of QSO points times the number of S/P/Cs worked on all bands (stations can be worked on multiple bands for QSO points and S/P/C credit) times the multiplier for station class. For example, if you work W2LJ on 20 and 40 Meters, it counts as 2 QSOs and NJ counts for a S/P/C on each band.

Bonus points – An extra 500 points can be added to your score if you operate near a lake, stream, river, pond, beach, etc. as stated above  Please send a photo of your set up, along with your log submission in order to claim points.

Suggested frequencies:
The QRP “Watering Holes”

For CW
80 Meters ~ 3.560 MHz
40 Meters ~ 7.040 and 7.030 MHz – also consider using from 7.114 to 7.122 MHz for a “slower” speed CW area.  We want to have everyone involved!
20 Meters ~ 14.060 MHz
15 Meters ~ 21.060 MHz
10 Meters ~ 28.060 MHz

For SSB
80 Meters ~ 3.985 MHz
40 Meters ~ 7.285 MHz
20 Meters ~ 14.285 MHz
15 Meters ~ 21.385 MHz
10 Meters ~ 28.885 MHz

These are suggested starting points, of course. Feel free to spread out and give your “Skeeter” wings a chance to do their thing.

Categories: CW Only and SSB Only, or Mixed Operating will be considered separate categories. Please indicate with your log summary which category you are participating as.

Log summaries, photos and soapbox comments can be sent to [email protected] no later than 14 days after the event.  Certificates will be issued to the top scorers of each category as well as others to be determined. Here’s an example of a summary that should be used:

Larry – W2LJ – NJ
Skeeter #4 – All CW
Skeeter QSOs – 23
Non-Skeeter QSOs – 5
DX QSOs – (if any)
S/P/Cs – 18
Station Class Multiplier X4
Claiming Bonus – No

If you send me all that information, I will figure out your score for you.

Hope to hear and work all of you during this year’s event. Special thanks to the NJQRP club for their sponsorship!

72 de Larry W2LJ
QRP – When you care to send the very least!

Larry Makoski, W2LJ, is a regular contributor to AmateurRadio.com and writes from New Jersey, USA. Contact him at [email protected].