AmateurRadio.com

Over the past couple of weeks, I’ve managed to steal away to the machine shop and continue to work on mounting the Schurr Einbau mechanism. I found a piece of polycarbonate in my scrap bin to make the interface between the Einbau and the base. It turned out that the mounting holes are tapped M3-0.5 so I had to make trip to Ace. While I was there, I picked up some brass screws also. Total cost of the project is 52.99 USD. I bored the holes in the base today with the milling machine and tapped them when I got home. Couldn’t resist putting it all together even though I haven’t finished polishing the base or the polycarbonate plate…

After some cautious first steps my first laser cut parts have been made. The case for the clubs upcoming WSPR kit build prototype has been, well, lasered.

There’s a couple of minor points to address but for a first effort I’m pretty pleased.

The idea was to cut for a single sheet a ‘desktop’ case for the U3 WSPR transmitter that could display a callsign or something similar on the front as a customisation as well as being simple and space efficient. Yep, you can buy a case but its quite nice to be able to make one in Cumbria rather than China. I should be able to get 4 and a half of them out of a single 300mmx600mm sheet.

All I have to do now is fix the faults and make it right next time.

Over the years, I’ve fancifully imagined that I would build a set of keyer paddles. I even went so far as designing a couple concepts and collecting materials…but, inevitably I moved on from the institution with the machine shop and sucker machinist who was showing me the ropes. About a week ago, Mike, W3MC, posted a bunch of goodies for sale, including a Schurr Einbau key mechanism. Since I love my Profi 2, I snapped it up, recalling also that I had a nice hunk of brass for a base. Today, I cut and milled a little base for it. Lots of finishing and some acrylic work remain, but for now, there’s something special about a freshly-milled hunk of metal.

After a few more weeks of not getting on the air I managed to man handle the portable Hexbeam up to about 4 above ground level (Note: must get that tilt base sorted out) to compare it against the Cobwebb I have in the loft.

So before we go down the ‘It’s not scientific’ route. I’m ok with that, no big deal its just a bit of fun.

There are some significant differences between the two antennas that I hadn’t fully appreciated. Firstly the noise levels on the Cobwebb were quite a bit higher, which seemed to make the Hexbeam sound quiet, when in actual fact there was no significant difference on the higher bands when it comes to S points. But, the lower noise levels made it much nicer to use. The image below shows what I mean. There is a band of ‘mush’ slap bang in the middle where I switched onto the Cobwebb. Just so you know, the Cobwebb was way quieter than the vertical I had before.

It’s not a huge visual difference on the screen but the ears make it obvious. The gain on the Hexbeam made it easy to make contacts with C06LA answering on the first call, I’d never expect that on the Cobwebb.

You can also see that the signal strength is fairly similar, that was W4UH calling CQ.

So not much in it when the Hexbeam is really low, I’m sure it’ll beat the pants off the Cobwebb at 12m but interesting to see that the Cobwebb is ‘noisier’. Especially as I thought it was quite a quiet antenna.

In this episode, your intrepid hosts discuss several ham-radio related stories including operators interfering with jail communications, getting lost in strange valleys, and transmitting through a hammock. But that’s only the beginning. Thanks for tuning, and for being a valued listener of our show.

73 de The LHS Guys

Sarah, Evan, and I had the opportunity to go to her parents’ place for the Easter holiday weekend. Since the trip coincided with the Michigan QSO Party, I decided this might be a good test of the portability of the K2. Unfortunately, I was unable to operate much longer than a half hour but I had some fun on 40 meters and tried out N3WG’s (Pignology) HamLog for logging. Neat stuff.

Saturday saw me opening a beer celebrating finishing off the new decking area…which means….Sunday saw me finishing off my portable hexbeam from Folding Antennas. The build took quite a while, about 8 for the hardware and about 3 for the layout and tuning. I’ve not used it much in anger as the rains started coming.

An early doors write up is here…..but so far its looking worth the build time. Here’s a shot of the half finished decking…oh and a half finished antenna.