AmateurRadio.com

The Chameleon CHA P Loop antenna

I had a chance to once again use my new Chameleon CHA P loop antenna  and it's now time to give this antenna my humble review. To begin with I shopped around for a loop antenna and looked at the following brands. The Alexloop walkham  loop, the Caras HF 315 loop, Alpha loop antennas and finally Chameleons CHA P loop antenna. Most of these antenna had good reviews for the most part but I chose the Chameleon CHA P loop for it's rugged construction and slightly better reviews. The loop comes with very easy to follow instructions that contain in-depth details about the antenna. I ordered it from DX Engineering and the delivery time was GREAT along with their customer service. The loop does not take long to assembly and wth practice I have it up and running in under 10 minutes. Below is a list of the positives I found with antenna:

1. It has a very small foot print when setup and is very portable which makes it easy for traveling on foot or bike. 
2. In very little time you can get very proficient as setting up the antenna. 
3. The Loop (LMR-400) section and PL-259 connectors are very good quality and also they are fitted with heat shrink to add a nice water tight fit. 
4. The tuning box is sealed and weather proof just for those days when Murphy decides to bring some rain on your portable operations. 

   The tuning box

5. The 6:1 reduction gear makes tuning accurate and finding the peak noise level very fast. On the tuning box I added a 40-10 meter decal to remind me of tuning direction. Also I added the DX Engineering sticker as I am blown away with their customer service. 
6. I was able to successfully tune the loop to at least 1.3:1 on all bands wether is was 10m or 40 meters. 
7. Once the antenna was tuned to the lowest SWR and you move away from the antenna the SWR does not change. In the past with other loop antennas I have used the tuning know was on the top of the tuning box. Your hand being in the loop would affect the SWR and once your hand was removed the SWR would change and this made tuning frustrating. Other loops did not have the 6:1 gear reduction and finding the sweet spot and lowest SWR was a challenge. The slightest touch of the tuning knob threw the SWR off and often you would have to start over again. 
8. On the base of the handle is a 1/4-20 female thread that makes putting this antenna on a tripod a breeze. Other loops I have used do not have this and I had to make up a homemade mount. 
9. RG-58 with integrated RFI choke feed-line decouples the Faraday coupling loop from the radio which is essential to prevent SWR fluctuation while rotating the antenna or moving the coax cable around.
10. If you have an HOA situation and getting on the air is a challenge this antenna could be the answer for you. 

    Quality PL-259 on Loop

The Chameleon CHA P Loop antenna

I had a chance to once again use my new Chameleon CHA P loop antenna  and it's now time to give this antenna my humble review. To begin with I shopped around for a loop antenna and looked at the following brands. The Alexloop walkham  loop, the Caras HF 315 loop, Alpha loop antennas and finally Chameleons CHA P loop antenna. Most of these antenna had good reviews for the most part but I chose the Chameleon CHA P loop for it's rugged construction and slightly better reviews. The loop comes with very easy to follow instructions that contain in-depth details about the antenna. I ordered it from DX Engineering and the delivery time was GREAT along with their customer service. The loop does not take long to assembly and wth practice I have it up and running in under 10 minutes. Below is a list of the positives I found with antenna:

1. It has a very small foot print when setup and is very portable which makes it easy for traveling on foot or bike. 
2. In very little time you can get very proficient as setting up the antenna. 
3. The Loop (LMR-400) section and PL-259 connectors are very good quality and also they are fitted with heat shrink to add a nice water tight fit. 
4. The tuning box is sealed and weather proof just for those days when Murphy decides to bring some rain on your portable operations. 

   The tuning box

5. The 6:1 reduction gear makes tuning accurate and finding the peak noise level very fast. On the tuning box I added a 40-10 meter decal to remind me of tuning direction. Also I added the DX Engineering sticker as I am blown away with their customer service. 
6. I was able to successfully tune the loop to at least 1.3:1 on all bands wether is was 10m or 40 meters. 
7. Once the antenna was tuned to the lowest SWR and you move away from the antenna the SWR does not change. In the past with other loop antennas I have used the tuning know was on the top of the tuning box. Your hand being in the loop would affect the SWR and once your hand was removed the SWR would change and this made tuning frustrating. Other loops did not have the 6:1 gear reduction and finding the sweet spot and lowest SWR was a challenge. The slightest touch of the tuning knob threw the SWR off and often you would have to start over again. 
8. On the base of the handle is a 1/4-20 female thread that makes putting this antenna on a tripod a breeze. Other loops I have used do not have this and I had to make up a homemade mount. 
9. RG-58 with integrated RFI choke feed-line decouples the Faraday coupling loop from the radio which is essential to prevent SWR fluctuation while rotating the antenna or moving the coax cable around.
10. If you have an HOA situation and getting on the air is a challenge this antenna could be the answer for you. 

    Quality PL-259 on Loop

The setup in the car

The CHA P loop

On Saturday wife and I had some errands to do in the town we used to live in, it's about an hours drive from were we are now. Julie had an appointment that would last for approximately 2 hours so I felt bringing the Elecraft KX3 would help pass this 2 hour time slot. I brought along my new loop antenna from Chameleon CHA P loop antenna . (A review of this antenna is coming soon) The weather was great and I had my spot preplanned out, it was along a river that flowed through town and there was a nice picnic table there that I have used in the past. Once I dropped of Julie for here appointment it was off to the river, I found there was a wedding shoot going on and the table was not gone! I then had to scope out a new spot which did not take long. The new spot was in a parking lot at the entrance to a park, not the same view as the river side setup but it will do. I was keying out CQ for about 1.5 hours with no answers but I did hear some stations but they were already in QSO's. I did check the Reverse Beacon Network to make sure my CW signal was getting out and it was, the conditions were good as well but I guess it was just time for me to give my CW fist a workout. As always Murphy seems to make his visit at least once on my outings. On this day Murphy decided to make my CW operations a bit more challenging. For a long time I have been using the Palm Radio's Mini Paddle. I find this paddle to be very smooth and very well made. A number of years ago the folks at Palm Radio sent me their newly revised cable that goes from the rig to the paddle. It was lighter and more easy to work with and a great improvement over the more bulky cable that was being used in the past.  I have owned this cable for about 5 years without any issues until yesterday on my outing. The end that plugs into the paddle had come apart, the two parts are held together by a screw. I thought at the time I just failed to check the screw and it came loose. I did not have a mini screw driver with me so I had to very carefully plug the connector into the key. Once I got home and upon closer look I realized the connector was broken and the only choice I had was to glue the two pieces together. I did this and it worked fine but in the end this is a one time fix. Overall I made no contacts but it was nice to get out and just have the enjoyment of getting on the radio and it's very relaxing.

Reverse Beacon Network

The setup in the car

The CHA P loop

On Saturday wife and I had some errands to do in the town we used to live in, it's about an hours drive from were we are now. Julie had an appointment that would last for approximately 2 hours so I felt bringing the Elecraft KX3 would help pass this 2 hour time slot. I brought along my new loop antenna from Chameleon CHA P loop antenna . (A review of this antenna is coming soon) The weather was great and I had my spot preplanned out, it was along a river that flowed through town and there was a nice picnic table there that I have used in the past. Once I dropped of Julie for here appointment it was off to the river, I found there was a wedding shoot going on and the table was not gone! I then had to scope out a new spot which did not take long. The new spot was in a parking lot at the entrance to a park, not the same view as the river side setup but it will do. I was keying out CQ for about 1.5 hours with no answers but I did hear some stations but they were already in QSO's. I did check the Reverse Beacon Network to make sure my CW signal was getting out and it was, the conditions were good as well but I guess it was just time for me to give my CW fist a workout. As always Murphy seems to make his visit at least once on my outings. On this day Murphy decided to make my CW operations a bit more challenging. For a long time I have been using the Palm Radio's Mini Paddle. I find this paddle to be very smooth and very well made. A number of years ago the folks at Palm Radio sent me their newly revised cable that goes from the rig to the paddle. It was lighter and more easy to work with and a great improvement over the more bulky cable that was being used in the past.  I have owned this cable for about 5 years without any issues until yesterday on my outing. The end that plugs into the paddle had come apart, the two parts are held together by a screw. I thought at the time I just failed to check the screw and it came loose. I did not have a mini screw driver with me so I had to very carefully plug the connector into the key. Once I got home and upon closer look I realized the connector was broken and the only choice I had was to glue the two pieces together. I did this and it worked fine but in the end this is a one time fix. Overall I made no contacts but it was nice to get out and just have the enjoyment of getting on the radio and it's very relaxing.

Reverse Beacon Network

An update from my last post regarding my Chameleon CHA P Loop antenna, the antenna bag zippers were repaired and the cost was 40.00 Canadian. I decided  to have some heavy duty zippers installed and I emailed DX Engineering and we agreed the cost would be 50/50. I submitted the bill to Maria at DX Engineering and to my surprise the total amount was covered! I emailed Maria about this and she told me she took the bill to her boss and he informed Maria to cover the whole cost. DX Engineering for sure is a class act!!
Lets move along to another class act.....I have been using Win4k3 suite software for rig control for over a year now. Tom VA2SFQ has software what will work with the Elecraft K3,K3S, KX3 and KX2. Tom has been updating the software on a very consistent basis. The software is very stable one just has to read Eham to see it's rated 4.9 out of 5. I have emailed Tom with some questions and he has replied very fast with a solution. Recently I had some issues and we were emailing back and forth to try to bring things to a resolution. On the weekend Tom asked me if I had Teamviewer (and I do) he wanted to use Teamviewer to take control of my PC and solve my issue once and for all. On Saturday evening I received a call from Tom on my cell and we linked my PC via Teamviewer and Tom took control. Tom stuck with me for 40 mins and he solved my issue and I was up and running again. I have never in all my days had this type of customer service. It is very obvious that Tom is committed to not only his software but to his customers. Tom was very pleasant on the phone as he sorted out the problem.

An update from my last post regarding my Chameleon CHA P Loop antenna, the antenna bag zippers were repaired and the cost was 40.00 Canadian. I decided  to have some heavy duty zippers installed and I emailed DX Engineering and we agreed the cost would be 50/50. I submitted the bill to Maria at DX Engineering and to my surprise the total amount was covered! I emailed Maria about this and she told me she took the bill to her boss and he informed Maria to cover the whole cost. DX Engineering for sure is a class act!!
Lets move along to another class act.....I have been using Win4k3 suite software for rig control for over a year now. Tom VA2SFQ has software what will work with the Elecraft K3,K3S, KX3 and KX2. Tom has been updating the software on a very consistent basis. The software is very stable one just has to read Eham to see it's rated 4.9 out of 5. I have emailed Tom with some questions and he has replied very fast with a solution. Recently I had some issues and we were emailing back and forth to try to bring things to a resolution. On the weekend Tom asked me if I had Teamviewer (and I do) he wanted to use Teamviewer to take control of my PC and solve my issue once and for all. On Saturday evening I received a call from Tom on my cell and we linked my PC via Teamviewer and Tom took control. Tom stuck with me for 40 mins and he solved my issue and I was up and running again. I have never in all my days had this type of customer service. It is very obvious that Tom is committed to not only his software but to his customers. Tom was very pleasant on the phone as he sorted out the problem.