Software-Defined Radio: Try Before You Buy? You Might Like It!

Sure! You don’t need to have a software-defined radio (SDR) before you start learning how to use the technology; there are a few different paths you can take, exploring and learning about SDR.

One way to gain some experience with SDR without spending a dime is to install a free software package for the very popular, non-Linux, operating system (that starts with ‘W’), and give SDR a test drive. If you like it, you might consider getting your own hardware (like the SDRplay RSPdx, for instance), and connecting it up to your computer and running this software, too.

Why I Dived Into SDR

I have always loved radio, ever since the early 1970s, when I discovered shortwave radio. In the last couple of years, I’ve had an increasing interest in the world of SDR. When I am working, but away from home (remember those days, before Covid?), I want to sample news and programming from around the world, but through shortwave. The way to do that, I found, is by using the various SDR options which allow a person to tune a remote receiver, and listen.

I also find working with the waterfall of a typical SDR-software user interface rewarding because, instead of blindly searching for signals in a subband, I can see all of the received signals on the scrolling time representation of a slice of frequency. Simply select that signal on the waterfall, and the radio tunes right to it.

I often connect to different SDR radios around the world, to catch all manner of shortwave signals, from maritime, military air, trans-oceanic air, or coast guard radio traffic, or other interesting HF communications including amateur radio CW and SSB signals. Occasionally, I also check out VHF and UHF signals from around the world. All of that, while instead an office building that is not suited for shortwave radio reception.

I’ve now decided to give back to the community; I’ve added my SDR receiver to the collection of receivers located around the world on the SDRSpace network of SDR radios.

My new SDRplay RSPdx software-defined radio receiver is live, via http://www.sdrspace.com/Version-3, using the SDR Console software (Version 3).

The receivers are online whenever I am not transmitting and when there are no local thunderstorms.

Antenna Port A is connected to a wire antenna (a horizontal 100-foot wire that runs out from my house’s chimney to a tall tree; about 10 feet of that wire is oriented vertically, where the wire passes through a pulley and then is weighted down so it can move with wind-driven tree movement), while Antenna Port B is connected up to a VHF/UHF discone.

Both antenna systems have an AM Broadcast band notch (reject) filter reducing local AM Broadcast-Band radio station signals by about 30 to 40 dB. I need to use these because the very close KLIN transmitting tower is just miles away and those signals overwhelm the receiver. When I use the signal filters, the local AM Broadcasting signals no longer overwhelm the receiver.

In the following video, I first explain my SDR setup, and in the second half of the video, I tune around the radio spectrum, using the software to control my SDR receiver.

A Couple of Questions

After watching this video, WO9B wrote an email to me. Michael asked of me two questions, summed up as:

1. Your SDR window has the IF screen on top. How is that accomplished?

2. Your AM Broadcast filters; more info, please. I live in the area of mucho broadcast stations and that looks like something I could use.

In the following video, I demonstrate how I changed my layout of the SDR Console software. And, I mention the AM Broadcast Filter for SDR Receivers (the hardware filter is found here: https://g.nw7us.us/3kU5SJN).

To Use My Receiver

Download the latest version of SDR-Console from https://www.sdr-radio.com/download – there is a 32-bit and a 64-bit Windows installation package.

The 64-bit installation package may be downloaded from one of these three sources:

1. Googlehttps://g.nw7us.us/3auBq44
2. DropBoxhttps://g.nw7us.us/310ooIG
3. Microsofthttps://1drv.ms/u/s!AovWaZDu7Hrd3U-yqK1bs3wuaFw2?e=o4nKeh

The 32-bit installation package can be downloaded from one of these three sources:

1. Googlehttps://g.nw7us.us/3iLasrZ
2. DropBoxhttps://g.nw7us.us/3g4VcVc
3. Microsofthttps://1drv.ms/u/s!AovWaZDu7Hrd3U4mJiiRtI9lm70s?e=HDG4ZX

Install the SDR Console package according to the directions given. Once you have the software installed, you will want to add my server. It takes some work to get familiar with the software, but there are online FAQs on how to begin.

One guide on how to add a server to the list from which you can pick may be found, here:

https://www.sdrplay.com/wp-content/uploads/2018/02/SDRConsoleV3-ServerGuide1-1.pdf

I worked on getting all of the bugs worked out of my installation before making the video. It did take some work, and reading up on things. But, the software is solid and a good contender against SDRuno, and HDSDR, and, this way I can share it online with you.

My server is known as, ‘0 NW7US‘ — it will be online when I am not using my antenna systems for transmitting. It will be offline during thunderstorms, or during times when I must use the systems for transmitting.

Look for the 0 NW7US server.

Software-defined radio is a great way to hear all sorts of communications, from local AM broadcast stations, FM stations, VHF Air Traffic, to shortwave radio stations including amateur radio HF communications.

Thank you for watching, commenting, and most of all, for subscribing; please subscribe to my YouTube Channel: https://YouTube.com/NW7US Also, please click on the bell, to enable alerts so that when I post a new video, you will be notified. By subscribing, you will be kept in the loop for new videos and more.

73 de NW7US

.. (yes, this is an expansion of an earlier post… forgive the redundancy… thank you) ..

Visit, subscribe: NW7US Radio Communications and Propagation YouTube Channel

3 Responses to “Software-Defined Radio: Try Before You Buy? You Might Like It!”

  • Rob - N1NTE:

    The KiwiSDRs online receivers are also available and there is no need to download any software… just use your browser (IE not supported). You can see a map of available receivers here:

    http://rx.linkfanel.net/

    You can visit my receiver here: http://sigmasdr.ddns.net:8073/

  • Chris - N3JLY:

    KiwiSDRs are a fantastic way to both “test drive” an SDR without needing to load software, as well as use remote receivers.

    I have a pair of them online, free for anyone to use:

    http://sdr.hfunderpants.com:8073/ is connected to a 120 ft T2FD antenna and

    http://sdr.hfunderpants.com:8074/ is connected to a 250 ft V Beam antenna directed to Europe (my QTH is in MD)

  • Rob, Chris:

    yeah, it is cool to see many different options to explore SDR. The web interface for the KiwiSDR is somewhat intuitive, and they work great. There are more bells and whistles in software like SDRuno and SDR Console, but not everyone needs that. In my case, I do need those extra features, so SDR Console is working as a fit for me. I do, however, want to add a few KiwiSDR radios to my line-up of online receivers, some day. Right now, I can’t buy hardware, because everywhere is sold out!

    73 de NW7US dit dit

Leave a Comment

Subscribe FREE to AmateurRadio.com's
Amateur Radio Newsletter
News, Opinion, Giveaways & More!

E-mail 
Join over 7,000 subscribers!
We never share your e-mail address.



Also available via RSS feed, Twitter, and Facebook.


Subscribe FREE to AmateurRadio.com's
Amateur Radio Newsletter

 
We never share your e-mail address.

Please support our generous sponsors who make AmateurRadio.com possible:

KB3IFH QSL Cards

Hip Ham Shirts

Georgia Copper
Expert Linears

morseDX

Ni4L Antennas

Ham-Cram
R&L Electronics

Do you like to write?
Interesting project to share?
Helpful tips and ideas for other hams?

Submit an article and we will review it for publication on AmateurRadio.com!

Have a ham radio product or service?
Consider advertising on our site.

Are you a reporter covering ham radio?
Find ham radio experts for your story.

How to Set Up a Ham Radio Blog
Get started in less than 15 minutes!


  • Matt W1MST, Managing Editor




Sign up for our free
Amateur Radio Newsletter

Enter your e-mail address: