AmateurRadio.com

I am a week delayed in documenting this adventure, however, I had to write about it. I went back to my QTH near Santa Fe on Father's Day weekend for some SOTA therapy. I needed to fuel my addiction. There is a great SOTA community in Santa Fe and the surrounding area. The area boasts four SOTA Goats (SOTA Progaram Activator Award), KT5X, KE5AKL, NM5S and the most recent K1JD. Needless to say any non-goats must understand that there are certain expectations. Accordingly, I hooked up with Doc, K7SO on the weekend to try to gain some ground on attaining, Goat Status.

On day one, Saturday, we activated three summits, Don Fernando (W5N/SS-024), 10900 (W5N/SS-019) and Greenie Peak (W5N/SS-015). These are all 10 point summits. My XYL, Cris, was also along to provide support and take few pictures.The equipment for the day was an FT-817, 20/40m EFHW for me and Doc had a KX3 with a 43 ft. random wire and a  9 to 1 balun. The weather was nice, clear to partly cloudy skies with 30 mph winds. The windy conditions put a haze in the air which dimmed the views a bit, but still not a bad day to be in the mountains.

The first two summits are east of  Taos, NM. Doc and I had done these summits before and with the coordinates where to park, getting these summits activated was a matter of course. Each requires relative short hikes to the top, but bushwhacking is the order of the day, with the ascent of Summit 10900 being the most diffiicult of the two. There are lots of downed trees that have to be navigated.

The main obstacle of the day was a recently fallen tree that blocked the road to Summit 10900. Not worry, my Jeep was able to get around the tree with a little off roading. A longer wheel base vehicle would have had trouble getting around. BTW, the jeep came in handy all day long, the roads we travelled had sections that the 4WD and high clearance came in handy.

We did see some wildlife during these activation, including several Elk, Whitetail Deer and some turkey.

Getting to Greenie Peak was more of challenge than we expected.  Greenie Peak is near Red River, NM, which is an hour plus drive from Summit 10900. I had done the peak in the past, but a friend had taken me there on a Razor, a two passenger ATV, and I didn't pay much attention. Consequently when the GPS sent us up the wrong road I willingly followed. This road was a 4WD only road, with warnings, and a sign that said "Exploration Road". Well, we were in search of Goat status, so onward and upward. The road was a one lane, rock filled, steep, hairpin switchbacks to a small summit only big enough to turn the Jeep around on. Sorry Doc, but this is not Greenie Peak. Back down we went. Finally found the road, made the Greenie Peak summit. To expedite the activation we only set up one rig and Doc and I alternated contacts. We worked the pile untill CQ's went unanswered and called it a day.

I had left my house at 7:30 am that morning to drive north to pick up Doc and finally got home that night at 10:30 pm. A 15 hour day of SOTA therapy. I was tired, but I did feel good about getting 30 activator points for the day.

Sunday was a new day, with two summits on the agenda. Barrillas Peak (W5N/PW-022) and Bear Benchmark (W5N/PW-014).  Doc was using this KX3 set-up again, but I swithed the the AT4-S, KD1JV designed CW only radio. The weather was a duplicate of the day before, but the wind had diminished considerably.

The hope was to get these two done and get a home alittle earlier. Barillas went off without a hitch. There is a firetower on top, with nice views. Propagation was good, but it was Father's Day, so I think a few of the chasers were occupied with other activities.

Getting to Bear Benchmark proved a little more challenging. My GPS is set-up for the shortest route which is good most of the time, but not for this day. We followed a road for several miles only to come to a locked gate with "No Trepassing" signs all over it. Bummer. It was getting late in the day and I felt that we wouldn't make the summit in time. We turned around, somewhat disappointed and headed back down. However, when we got back to the main road, I wanted to find the right road at least. We reentered coordinates and the GPS point us a different direction, which to make a long story short, was the right direction. Once on the right road, we decided to go for it and when finally reached the firetower atop Bear Benchmark, the determination was rewarded. We, again, only set-up one station, and took turns calling CQ until we had worked down the pile.

I made it home just in time to watch my favorite basketball team, the San Antonio Spurs put a beat down on the Miami Heat and win the NBA Championship. A good day indeed.

Below is a brief  video of our adventure. I must give credit to Cris who gets credit for putting this together.


Mike Crownover, AD5A, is a regular contributor to AmateurRadio.com and writes from Texas, USA. Contact him at [email protected].

I have dusted off the Ultimate3 QRSS beacon kit that I built earlier in the year while a foundation licensee. Having progressed to a intermediate licence I can now operate something I've constructed.



Until now it has been attached it to a dummy load with the FUNCube Dongle Pro+ SDR in close proximity as a receiver for experimental purposes.

One unresolved issue was it being consistently off frequency. The DDS modules used are prone to temperature fluctuations and component variances so the Ultimate 3 has the option of using a GPS module to provide both an accurate time source and an accurate 1PPS input which can be used to self calibrate. Except in my case it had proved to be unreliable.

I am using one of the inexpensive GY-GPS6MV2 modules containing the U-Blox chipset I posted about previously with the additional tap off to provide the 1PPS TTL signal.

Initially the GPS module was connected in close proximity to the Ultimate3 but struggled to maintain lock probably due to interference from the DDS module. Even when lock was achieved the calibration never seemed to work. I posted a question on the yahoo support group and from the answers I verified the calibration setting were correct so the only likely culprit was the quality of the 1PPS signal.

The serial NMEA sentences and the 1PPS signal from the GPS are likely to be required in other planned projects, such as an 'shack clock' and a GPS disciplined frequency standard. So I decided to put the GPS module  into a waterproof housing that can fitted on the shack roof in clear view of the sky and away from any potential interference. A multi-cored cable supplies power and the TTL RX/1PPS signals being fed back to the bench.

Sourcing an inexpensive weatherproof enclosure (£2) and waterproof cable gland were straightforward enough. I mounted the GPS module on a piece of strip board and replaced the on board LED with one mounted in the enclosure so I easily determine if the GPS had achieved lock, since it only flashes when it has. The LED is sealed with epoxy resin. It should be noted that the outputs of the U-BLOX chip are only rated at 10mA so bear it mind when selecting an LED and calculating the current limiting resistor. The connecting cable is some surplus unscreened alarm cable fitted with a couple of ferrite clamps.


The GPS now has no trouble achieving lock and quickly sets the Ultimate3 clock. Researching the 1PPS problem I hadn't come up with anything definite, as the signal looked okay on the oscilloscope. But I decided to fit a 10K resistor pull up resistor between the 1PPS output and the 3.3V supply on the GPS module. If this actually made the difference I have no idea but the Ulimate3 now successfully calibrates the DDS using the GPS.

At the moment I have configured the beacon to run WSPR and I have been spotted by other operators. Initially I wasn't getting much RF out of the device and it turned out to be a combination of poor connection caused by me not removing the enamel properly on a toroid winding and an iffy antenna connector. Both have been corrected and now get a measurable deflection on the SWR/Power meter. With the additional of a second power amplifier FET it is around 200-250mW.



I purchased the Ultimate3 with a low pass filter for the 40M band and while I have had some European spots the results have been a little disappointing. 40M has turned out to be almost unusable at my QTH due to QRN/M so not sure if that is having an effect, also the antenna I have isn't naturally resonant on 40M so is going through a tuner which will certainly be introducing some losses, without the tuner the FETs get very warm!

With this in mind I have purchased some additional LPFs for the 30M and 20M bands and the LPF relay switching board for the Ultimate 3 so can try/run multiple bands.
Andrew Garratt, MØNRD, is a regular contributor to AmateurRadio.com and writes from East Midlands, England. Contact him at [email protected].

Over the years, there have been plenty of attempts to bridge the Atlantic on 144MHz, via tropo or meteor scatter. Up to now, it hasn’t been done. There’s no doubt at all in my mind that it’s possible – it’s just a question of try, try and try again.

A North America group, operating as VC1T plan to try from July 5th to 12th this year. They plan to use good power to a 43 element yagi (yes, 43 elements) and concentrate on FSK441 and JT65b modes.

You can read more about their plans here

Will this be the year it’s done? Wouldn’t it be great if the answer was yes!

Tim Kirby, G4VXE, is a regular contributor to AmateurRadio.com and writes from Oxfordshire, England. Contact him at [email protected].

36 intrepid souls have signed up for the 2014 NJQRP Skeeter hunt since the opening bell rang early yesterday morning. And I am proud to say that one of our Skeeters this year is Mr. NJQRP himself.  George N2APB sent an e-mail and was assigned Skeeter #29.

I also see that several of my fellow QRP Polar Bears have signed up for numbers, too.  These guys are fantastic and are never ones to miss the opportunity for an outdoor QRP adventure. Thank you fellow Polar Bears – grrrrrrrrrrr. Will be looking to join you in swatting Skeeters from bear hide this August.

I’d like to take this opportunity to “borrow” and old New Jersey slogan.  This was an advertisement that ran back in the days when Tom Kean was governor and it was designed to increase tourism in NJ.  It went like this, “New Jersey and you ….. prefect together.”

If I may, this kind of sums up the whole idea and intent behind the NJQRP Skeeter Hunt.

“QRP and the great outdoors ….. perfect together!”

Join us and see for yourself.

72 de Larry W2LJ
QRP – When you care to send the very least!
2014 Skeeter #13

MONDAY MORNING IMPORTANT UPDATE:  Argggghhhhh!  I went to my spam file this morning and found about 20 Skeeter Number requests that were sent over the weekend. I didn’t know they were there, and I didn’t even think to check there until this morning!  So if you sent me an e-mail request over the weekend and still haven’t heard from me …..you will tonight. I promise!

Larry Makoski, W2LJ, is a regular contributor to AmateurRadio.com and writes from New Jersey, USA. Contact him at [email protected].

With the summer season definitely here, Joyce (K0JJW) and I climbed W0C/SP-089, an unnamed summit east of Buena Vista near Trout Creek Pass, for a Summits On The Air activation.  This summit is also referred to by its elevation: 10525. The mountain is quite majestic with a large rock face that rock climbers enjoy climbing.

To reach the summit, we drove a 4WD truck from Trout Creek Pass on Forest Service Road 311, connecting to FS Road 373. Four wheel drive is required for this road due to the steep sections, which may not be passable in muddy conditions. You can also approach from the Buena Vista side, see the San Isabel Forest Service Map. From 373 we took a side road (shown in blue on the map below) that is not always shown on maps. I believe it is marked 373A but I am not sure. We parked the truck at the lat/lon shown.

From there we hiked a non-technical route to the west of the summit, working our way up through the draw shown on the map. There were a few faint game trails here and there but mostly it was some challenging bushwhacking up that draw. The willows and sticker bushes made us glad that we had long pants on.  Also, there was quite a bit of downed timber to step over. The route got quite a bit easier once we got to the top of the draw, but still no trail. The elevation gain was only 1100 feet but it felt like a lot more work than that.

As we neared the summit, I heard Bob (W0BV) calling me on 146.52 MHz. I had put out an email alert to some of the hams in the area so Bob and some others knew I was going to be out climbing. Once I got to the summit, I contacted Bob (W0BV) and quickly had a mini-pileup with several stations calling me. Mark (KF5WCY) visiting from TX gave me a call, followed by Carl (K5UK) near Mount Yale. Then I worked Jim (KD0MRC) in Buena Vista and Larry (KL7GLK) in Leadville. Thanks, guys, for getting on the air and contacting me!

I used my Yaesu FT-60 handheld transceiver and a 1/2-wave vertical antenna for these contacts. While I had my 3-element Yagi antenna with me, I did not bother to set it up.

My spouse and hiking companion Joyce (K0JJW) and I have worked out a standard SOTA activating procedure. As we get close to the summit, she stops below the activation zone and I continue to the top. Then I work her on 146.52 MHz which guarantees a successful activation. It is possible to get skunked on 2m fm in the backcountry, so this is good insurance. This one QSO does not result in any SOTA points, since the rules require a minimum of four contacts for activation points. Next, Joyce joins me on the summit and we work whoever is out there. Lately, I’ve had pretty good luck getting at least 4 contacts on 2m fm. On the descent, she stays on the summit and I go down the mountain and work her once I am outside of the activation zone. That way, I am able to work the summit, too.  Then she leaves the summit, catches up with me and we descend the rest of the way together.

For more information on VHF SOTA activations, see How To Do a VHF SOTA Activation.

73, Bob K0NR

Bob Witte, KØNR, is a regular contributor to AmateurRadio.com and writes from Colorado, USA. Contact him at [email protected].

It turns out my recent message purporting to have been sent for the International Space Station (ISS) was not from there at all, but from a tent in Wales! Not quite sure why people get a kick from this? It all seems a bit silly to me. Previously this person’s account was sending out dodgy links and I informed him of this.  Be warned – all may not be what it seems.

Roger Lapthorn, G3XBM, is a regular contributor to AmateurRadio.com and writes from Cambridge, England.

After a long, cold Sprinter (that’s what you get when Winter seems to last endlessly into Spring), Summer is finally here! Yay! And as promised, as of today, numbers are being assigned for the 2014 NJQRP Skeeter Hunt.

The Hunt will be held on Sunday August 10th this year – and right now, the best place to see the rules is at  http://w2lj.blogspot.com/p/njqrp-skeeter-hunt.html. I am trying to get the QSL.NET page updated with the new bonus points rules, but the server seems to be down right now.

Yes – bonus points this year for gathering enough letters from callsigns to spell out the word “SKEETER”. 100 extra points will be added to your score if you accomplish this feat. In any event, the NJQRP Skeeter Hunt is a grand time and folks seem to enjoy themselves a lot, so send me an email ([email protected]) and reserve your Skeeter number today.

Today was also the Raritan Valley Radio Club annual hamfest, which is held at Piscataway High School, in Piscataway, NJ.  The weather was absolutely beautiful – perfect for a hamfest!  It was sunny and it got up into the high 70s.  Very nice, but yet not exasperatingly hot. And as you can see from the two quick photos that I snapped with my phone, there was not a cloud in the sky. Unfortunately, it was perfect sunburn weather. Reporting time for the hamfest workers was 5:00 AM and as I was driving to the hamfest site, I had realized I had forgotten to bring sunscreen.  I discovered the hard way that there are NOT a lot of places open at 5:00 AM where you can buy sunscreen!

There were plenty of vendors and lots of buyers. The ARRL had a presence with the appearance of Bill Hudzik W2UDT, our section Vice Director. (Psst!  It helps that he’s a club member!) We also had a VE Exam session, where three people earned their Technician licenses, and we also had one upgrade to General and one upgrade to Extra.

In the top photo, you can see the huge mast sticking up from an old broadcast van that Brian N2MPM had acquired. Running up the mast was a PAR END-FEDZ antenna that Alan W2AEW using to make QRP contacts.  If you follow this blog, you know that I have mentioned Alan’s YouTube videos in the past. He does an excellent job producing videos on how to use test equipment and other neat technical tutorials. If you haven’t subscribed to his YouTube channel, then you are cheating yourself. After you read this go over and subscribe – it’s definitely worth it.

Here’s a video he took of today’s festivities:

Pulling off a hamfest like this is a huge undertaking. Thanks to the direction of our two Hamfest Committee Chairmen, Drew W2OU and Rich W2PQ and all the members of the RVRC, this comes off flawlessly – year after year.

In between my duties of assisting with the parking and placement of the vendors, and being the lead in administering the VE session, I did get a chance to look at the various wares on the tables.  I purchased some BNC to PL259 adapters and some large alligator clips that we will to connect to batteries that we will be using next weekend during Field Day. Not a big spender much to the discontent of the vendors, but much to the delight of my wife.  😉

I’ve been up way too long and am making way too many typos – even more than I usually make, so it’s off to the sack for W2LJ. (Thank God for spellcheck.)

72 de Larry W2LJ
QRP – When you care to send the very least!
Skeeter #12 for 2014

Larry Makoski, W2LJ, is a regular contributor to AmateurRadio.com and writes from New Jersey, USA. Contact him at [email protected].