Amateur Radio Weekly – Issue 67

Field Day 2015 round-up

All female amateur radio group on Field Day
The Southern Mississippi YL Amateur Radio Club formed in 2008 to encourage women to get more involved.
WLOX

W3AO Field Day
Wind and rain cannot stop us from broadcasting. Even a “little” rain, like close to four inches on Saturday. Our annual weekend emergency ops practice, aka Field Day, went on as planned.
W3AO

(photos) W3AO Field Day 2015
W3AO

(video) Field Day 2015 – QRP with the Yaesu FT-817 in the pouring rain
How many contacts can be made with QRP SSB during Field Day using a modest station in bad weather? Join me and let’s find out.
YouTube

Field Day Results
Field Day is not really about A-list operators, it’s an event for the every-man.
KE9V

(video) Chattanooga Amateur Radio Club practices in event of crisis
It’s mostly for fun, but this radio field day has a purpose too, and that’s to keep everyone prepared in the event of a crisis.
WRCB

Top links

FCC invites comments on rules for new LF and MF amateur allocations
The FCC is inviting comments on its recent proposals to authorize Amateur Radio operation on two new bands – an LF allocation at 135.7 to 137.8 kHz (2200 meters), and an MF allocation at 472-479 kHz (630 meters).
ARRL

FreeDV 700
We’ve just released FreeDV v0.98 GUI software, which includes the new FreeDV 700 mode. This new mode has poorer speech quality than FreeDV 1600 but is far more robust, close to SSB on low SNR fading HF channels. Mel Whitten and the test team have made contacts over 1000 km using just 1 Watt!
ROWETEL

Hawaii, Washington State QSO on 2 meters
The difficult and rare path between Washington state and Hawaii has been worked in the past … lastly in 1995, when some alert ‘7s’ found themselves in KH6HME’s logbook.
VE7SL

HamShield for Arduino (VHF/UHF transceiver)
The HamShield supports both voice and packet radio modes through a wide range of VHF and UHF frequencies: 2 meter (144-148 MHz), 1.25 meter (220-225 MHz), and 70 centimeter (420-450 MHz).
Kickstarter

A Maker’s introduction to Ham Radio
First, you’re a Maker, so you already have a lot in common with the ham radio community. Hams are tinkerers, builders, fixers, and inventors by nature.
Make:

RF Breakout Kit for the Raspberry Pi
An expansion board supplied as a self-assembly kit, designed for experiments with the Raspberry Pi as a radio frequency source or radio transmitter using the programmable clock generator built into the Pi’s processor.
Kickstarter

(podcast) 100 Watts and a Wire
100 Watts and a Wire is a program celebrating amateur radio through the eyes of a new ham. The show will feature topical conversation and interviews, news and an entertaining look at the adventures of a ham trying to figure it all out.
K0STH

Senate sponsor of Parity Act said bill promotes equality
US Senator Roger Wicker (R-MS), who sponsored “The Amateur Radio Parity Act of 2015” in the Senate, had said the bill he introduced, with original cosponsor Richard Blumenthal (D-CT), would allow for transparency and equality in the regulatory process.
ARRL

How to

Building an APRS IGate
Setting up an IGate is an easy way to contribute to the strength and utility of the APRS network without overwhelming the RF side of things.
WCARES

Using the RTL-SDR as a transmitter
After performing the hack the RTL-SDR is able to output a signal anywhere between 1.8 GHz to 3 GHz.
RTL-SDR.com


Amateur Radio Weekly is curated by Cale Mooth K4HCK. Sign up free to receive ham radio's most relevant news, projects, technology and events by e-mail each week at http://www.hamweekly.com.

Radio Programming: CHIRP vs. RT Systems

chirp-vs-rt-systems

Two of the big names in radio programming are CHIRP and RT Systems. But which one should you choose?

CHIRP is free, open source software that’s used with a third-party programming cable. RT Systems makes commercial programming kits which include both  software and a radio-specific cable.

CHIRP supports a large number of radios including:

  • Anytone
    AT-5888UV
  • Baofeng/Pofung
    F-11, UV-3R, UV-5R and variants, UV-6, UV-82/82L/82X, GT-5, UV-82C, UV-B5/B6, BF-666S/777S/888S, GT-1, BF-F8HP
  • Icom
    IC-80AD, IC-2820H, ID-800H, ID-880H, IC-208H, IC-2200H, IC-91/92AD, IC-V/U82, ID-RPx000V/RP2x, IC-2100H, IC-2720H, IC-T70, IC-T7H, IC-T8A, IC-Q7A, IC-W32A, IC-746, IC-7200, IC-7000, ID-31A, ID-51A
  • Kenwood
    TH-D7A/G, TH-D72, TH-F6A, TH-F7E, TH-G71A, TH-K2, TK-7102/8102/7108/8108, TM-271A, TM-281A, TM-D700, TM-D710, TM-G707, TM-V7A, TM-V71A
  • Yaesu
    FT-1D, FT-60R, FT-90R, FT-817/ND, FT-857/D, FT-897, FT-1802M, FT-2800M, FT-1900R/2900M, FT-7800R/7900R, FT-8800R, FT-8900R, FTM-350R, VX-170, VX-2R, VX-3R, VX-5R, VX-6R, VX-7R, VX-8R
  • Wouxun
    KG-UVD1P, KG-UV2D, KG-UV3D, KG-UV6D, KG-UV6X, KG-UV8D

The RT Systems software supports a much larger array of radios:

  • Alinco
    DJ-A10, DJ-A40, DJ-100, DJ-175, DJ-G7, DJ-G29, DJ-V17, DJ-V27, DJ-V47, DJ-V57, DR-03, DR-06, DR-135, DR-138, DR-235, DR-435, DR-635, DR-638, DX-SR8
  • Anytone
    AT-398, AT-518UV, AT-588, AT-3208, AT-3318UV-A, AT-3318UV-C, AT-3318UV-D, AT-3318UV-E, AT-5189, AT-5888UV, ANILE-8R, NSTIG-8R, OBLTR-8R, TERMN-8R
  • Baofeng/Pofung
    997-S, BF-F8, BF-F9, BF-388A, BF-530, BF-888, GT-1, GT-3, GT-5, UV-B5/B6, UV-5R, UV-E5, UV-8HX, UV-F11, UV-66, UV-82, UV-89, UV-920, UV-TEN4
  • Icom
    IC-R2, IC-T2, IC-R6, IC-Q7, IC-T7, IC-T8, IC-V8, IC-R10, IC-R20, IC-W32, IC-T70, IC-80, IC-V80, IC-T81, IC-U82, IC-V82, IC-V85, IC-T90, IC-91, IC-92, IC-208, IC-746, IC-756 PRO, IC-2100, IC-2200, IC-2300, IC-2720, IC-2730, IC-2820, IC-7000, IC-7100, IC-7200, IC-7410, IC-V8000, IC-9100, ID-31, ID-51, ID-51+, ID-800, ID-880, ID-5100
  • Kenwood
    TH-K2, TH-F6/F7, TH-D7G, TH-K20, TH-D72, TM-V7A, TM-V71, TM-271/281, TM-471, TM-D700, TM-G707, TM-D710, TM-D710G, TS-480, TS-590, TS-590G, TS-2000
  • TYT
    TH-UVF1, TH-UV3R, TH-UV6R, TH-UV8R, TH-UVF9, TH-UVF9D, TH-UVF8000D, TH-9000,  TH-9800
  • Wouxun
    KG-UV23, KG-UV1DP, KG-UV5D, KG-UV6, KG-UV8D, KG-UV899, KG-UV920P, KG-UV950P
  • Yaesu
    FT-1D, FT-50, FT-60, FT-90, FT-250, FT-270, FT-277, FT-450, FT-817/D, FT-847, FT-857/897/D, FT-950, FT-991, FT-1500, FT-1802, FT-1807, FT-1900, FT-1907, FT-2600, FT-2800, FT-2900, FT-3000, FT-7100, FT-7800, FT-7900, FT-8000, FT-8100, FT-8500, FT-8800, FT-8900, FT-DX3000, FT-DX1200, FTM-350, FTM-400, VR-160, VR-500, VX-1, VX-2, VX-3, VX-5, VX-6, VX-7, VX-8/D, VX-8G, VX-110/150, VX-120/170, VX-127/177

Both CHIRP and RT Systems support several other less popular radios not listed above.

Here are my questions:

Have you used CHIRP or RT Systems programming software? What are your thoughts?

If you’ve used both, is it worth spending $49 on the RT Systems programming kit if your radio is supported by CHIRP?

Leave your answer as a comment!


Matt Thomas, W1MST, is the managing editor of AmateurRadio.com. Contact him at [email protected].

KL7 Tropo?

courtesy: http://www.nrlmry.navy.mil/
In a QSO yesterday with Mike, VE7SKA, on Saltspring Island, he alerted me to what appears to be a possible tropo path forming between here and KL7. Mike is, as far as I know, the only VE7 to have heard the KH6HME 2m tropo beacon (on several occasions) and even had a partial two-way with KH6HME in the 1995 duct to the PNW.

Like our unprecedented early hot and stable weather pattern over the West coast, this path is fairly rare and has never really been explored ... this one appears to be forming a stable path towards Alaska. The predicted conditions can be viewed on Bill Hepburn's World Wide Tropospheric Ducting Prediction page. Select the Eastern North Pacific from the 'Region' drop-down menu and see the map for Saturday.

Perhaps there are some KL7s near the water, or not too far inland and with a clear shot towards the southeast, that would be interested in running some possible tropo tests over the next few days if the path shapes up as predicted in the Bill Hepburn maps for the weekend. Not ever having explored this possible path before might yield some interesting results ... and who knows how far south into Puget Sound a tropo signal from the north might reach? Maybe it's time to find out. Of course, any stations between here and northern KL7 (Prince Rupert?... Juneau? ... Ketchikan?) might also be interested in trying a possible 2m path.

Steve McDonald, VE7SL, is a regular contributor to AmateurRadio.com and writes from British Columbia, Canada. Contact him at [email protected].

2015 Field Day

I was able to get out and participate in local Field Day activities with my club, the Benton County Radio Operators. We were out at a private facility out in the country, and ran off of battery and generator power for the event. I worked PSK31 on 20 meters alternating with another club member all day on Saturday. This was the first time I have had my entire station out in the field since building my box. I was also able to use one of my homemade antennas. The chosen antenna for the day was my homemade Buddistick configured for 20 meters. The painters pole holding up the antenna was guyed using parachute cord and three cement blocks as the anchors. The setup was easy to put up and take down and worked well. Since this is the same station and antenna I also use at home, there was really nothing new to try out, so it all had been thoroughly tested before Field Day.

2015 06 27 18 17 18 2015 06 27 16 05 23

Wayne Patton, K5UNX, is a regular contributor to AmateurRadio.com and writes from Arkansas, USA. Contact him at [email protected].

The Spectrum Monitor — July, 2015

tsm072015

Radio Memories
By Lawrence E. DeMilner W1TA

The benefits of amateur radio would eventually pay lifelong dividends for a 12 year-old boy, sitting for his Novice license exam 62 years ago. After being interviewed on the Today Show as a Boy Scout, he would later spend seven months as an American ham in the USSR at the height of the Cold War. Later still, he would spend three years as one of the scarcest DX calls in the world. It was all because of amateur radio.

XER – King of the Mexican Border Blasters
By John Schneider W9FGH

From its inception, radio has attracted more than its share of schemers and outright con artists. The story of John Brinkley and his questionable medical services, which allowed him to mass a personal fortune, is the story of one man dodging lawsuits and legislation designed to bring him down. But, before that could happen, he had built the most powerful radio station in the Western Hemisphere and turned it into a cash-generating machine.

When Our Vintage Radios Fought in the Air War
By Richard Fisher KI6SN

From post-war radio frenzies, created by a massive military-surplus market, grew a thirst among shortwave listeners and radio amateurs to acquire the gear that served so admirably in the skies—especially during World War II. Most of these receivers, transmitters and their accessories were top performers, and yet they were quite inexpensive on the surplus market. They were golden back then, just as they are today. Richard charts the history of radio and aviation.

Watts Up? Line Voltage for Vintage Radios
By Rich Post KB8TAD

Recently, Rich Post measured the AC voltage in his home electric circuits: 123.5 volts. According to the American National Standards Institute (ANSI), that is well within the accepted service range of 114 to 126 volts for line voltage, which is nominally 120 plus or minus 5%; a range hasn’t changed since the original ANSI standard was published in 1954. He asks, “My refrigerator and microwave oven might be happy at 123.5 or even 126 volts, but what about my vintage radios?” Rich shows us how to safely reduce the voltage that our vintage sets work best at.

Multiple Satellite Reception from a Single Ku-Band Dish (Part 1)
By Mike Kohl

Direct Broadcast Satellites, such as DirecTV and DISH Network, are positioned close enough in the Clark Belt to allow several LNBFs mounted on a single dish to receive the satellites that make up their programming lineup of hundreds of channels. But, Free-to-Air satellites are spaced considerably further apart and transmit at considerably less power. Can FTA hobbyists employ this same technique? Mike has been experimenting with this for years and has achieved some pretty amazing results. He tells us how it’s done.

Scanning America By Dan Veenaman
EDACS, Talkgroups and RF Explorer

Federal Wavelengths By Chris Parris
FBI Aircraft in the News

Utility Planet By Hugh Stegman NV6H
U.S. Navy-Marine Corps MARS Closes

Digital HF: Intercept and Analyze
By Mike Chace-Ortiz AB1TZ/G6DHU
Swiss Diplomatic Network undergoes Changes

HF Utility Logs
By Mike Chace-Ortiz and Hugh Stegman

Amateur Radio Insights
By Kirk Kleinschmidt NT0Z
Six Meters: A New Twist on the Old Magic

Radio 101 By Ken Reitz KS4ZR
The Wi-Fi Scanner, SWL Option

Radio Propagation By Tomas Hood NW7US
The 10.7-cm Radio Flux

The World of Shortwave Listening By Keith Perron
Community-based Radio helps Nepal Recover after Earthquake

The Shortwave Listener By Fred Waterer
Sputnik Radio, BBC and the VOA

Maritime Monitoring By Ron Walsh VE3GO
Maritime Station Consolidation

The Longwave Zone By Kevin O’Hern Carey WB2QMY
BBB-4 Wrap-Up

Adventures in Radio Restoration By Rich Post KB8TAD
Powering the Zenith 5K037 “Farm” Set with AC and Forming a Dial Cover

The Broadcast Tower By Doug Smith W9WI
License? I don’t need no stinking license!

Antenna Connections By Dan Farber AC0LW
Round and Round, Part II: Jolly Green Delta Loop

Radio Horizons
Channel Master DVR+ Adds Streaming to OTA-TV

The Spectrum Monitor is available in PDF format which can be read on any desktop, laptop, iPad®, Kindle® Fire, or other device capable of opening a PDF file. Annual subscription (12 issues, beginning with the January 2015 issue) is $24. Individual monthly issues are available for $3 each.


Ken Reitz, KS4ZR, is publisher and managing editor of The Spectrum Monitor. Contact him at [email protected].

KH6 On VHF


I notice that the long distance records for terrestrial QSO's on 2.3 and 3.4GHz were recently broken. The records were set by veteran VHFer N6NB, Wayne Overbeck and W6IT, Greg Campbell. N6NB was operating portable in Hawaii while W6IT was operating Wayne's home station near Orange, California. Both contacts were on SSB. In Overbeck's own words as posted on the Tropo Ducting Reports reflector:

I'd like to post something about my trip to Hawaii for the current tropo duct. This trip has really turned out well so far.

Last week the Hepburn forecast suggested that a duct might form in a few days. So I bought an airline ticket and packed a station for
all bands from 144 MHz through 10 GHz in two large suitcases plus a roll-aboard and a backpack (total weight: 150 pounds). When I got here, I rented a small SUV and built a station in/on it. I made several trips to Home Depot for parts to build a rotating roof platform.

When the duct began on Tuesday, I drove all over Mauna Loa while listening to my own 222.030 MHz beacon in Orange County, Calif. It was a thrill just to hear it 2,500 miles away. By Thursday, the duct seemed to be at its best. Greg, W6IT, activated my hilltop station near Orange, CA and we worked Thursday night on six bands, including 2304 and 3456 MHz, both for new world DX records. I heard Greg well on two more bands, 902 and 5.7 GHz, but so far local QRN in Orange County has prevented him from hearing me on those
two additional bands. Let's hope the duct continues for a little longer so we can try again and also work more stations on the west coast.

I intend to write at least a conference paper and create a PowerPoint show about what I've seen and heard in Hawaii. I've noticed that the KH6HME beacon site, as good as it is, sometimes seems to be above the cloud layer that forms the top of the duct. Thursday night it was about 2,000 feet above the cloud tops. Seeing that, I drove down to 5,200' elevation to work Greg on all those bands. (The beacon site is about 8,200 feet above sea level.) My 222 beacon was definitely louder at lower elevations than at the beacon
site at that time. Friday night I operated at 7,300', which was near the cloud tops and where my beacon seemed loudest then. The size and elevation of the duct seems to vary a lot, perhaps explaining the way the KH6HME beacons vary in relative signal strength, with 432 being a louder at certain times while the 144 beacon is louder at other times. There are some very interesting natural phenomena at work here.

If anyone would like to watch a video of the record-setting 2304 QSO with W6IT, it's online on my website:
www.n6nb.com/2304rcrd.mp4 Thanks to Greg, W6IT, for his able operating on the other end of these QSOs.

73, Wayne, N6NB/KH6


With the present extremely hot stable weather on the west coast, chatter on the PNWVHF reflector suggested that operators on the coast as far up as Washington state should be watchful of any possible DX opportunities should a suitable ducting pattern form between KH6 and the coast.

The difficult and rare path between Washington state and Hawaii has been worked in the past ... lastly in 1995, when some alert '7's' found themselves in KH6HME's logbook. Paul, K7CW and Merle, W7YOZ described an exciting day from Washington state:

I'll never forget that event. On June 30, 1995, KH6HME was worked by two guys in the Aberdeen, Washington area on 2m. The next day, July 1, I drove my pickup down to the area and went to a place suggested by one of the guys (this place now has the Langley Hill weather radar installation). I had a partial contact with KH6HME, but he got my call wrong and I couldn't easily reposition my antenna as it was fixed on the vehicle, and we couldn't complete. I sat back and listened to the other guys make contact with Paul. Dejected, I drove back home. Next day, July 2, though, I got my reward. Six meters opened to Japan in a nighttime sporadic E opening. I had my first QSO with a JA. It was with a JA6 in the far southwest of Japan. And I subsequently had 150 more QSOs with JA stations during that opening. I worked all 10 JA call districts, qualifying for the AJD award. My rig was running 80 watts and my antenna was a home brew 5-element yagi about 15 feet above the ground. This was a huge opening and there have been very few like it since.

So, after the big 2m tropo event, switch to 6m for another biggie.

73, Paul K7CW

Indeed an unforgettable time. W7FI first worked KH6HME, then phoned me and I got out of bed and heard WM7A (K7NQ) working him and then I worked him followed by N7MWV after I called and got him out of bed. K7CAI had a partial but was at the edge of the duct and Paul could never quite get Ozzie's quirky phonetics " K7 Cowboys And Indians" - a lesson for me to always use standard phonetics. KH6HME was S7 and over with his 60 Watts at my Kirkland, WA QTH for nearly an hour - long enough for me to call KK7B in MI and got him out of bed to listen over the phone. Paul's QSL along with that of WA4CQG in AL who I worked on 2 Meter double hop E's on another unforgettable evening in 1988 occupy a prime spot in my Ham Shack

Then the JA's on 6 the following evening was almost too much to believe. 

Merle W7YOZ

Although the KH6HME VHF/ UHF beacons are still in operation, sadly, there appears to be no VHFers able to visit the beacon site and work the mainland, should an opening occur. Fred, KH7Y, the most recent beacon caretaker, has since moved back to California, leaving a giant hole in the VHF scene on the big island. I wonder if there is a replacement capable of activating the station?

Even without any operators at the far end, it would be exciting to just hear the VHF beacon(s) in this region. The 2m beacon, now on 144.277MHz, has even been heard here in BC, by Mike, VE7SKA, listening from his hilltop location on SaltSpring Island. Unfortunately no two-way contact was established at the time. Tropo of any kind is a rare event east of Vancouver Island's west coast because of the mountainous terrain.

One of the best ways to follow the formation of favorable conditions is to watch the tropo prediction maps on Bill Hepburn's website as well as the visible west coast weather patterns available here.

An interesting summary of the 1995 openings, as well as the associated weather pattern pictures, makes for fascinating reading on the PNWVHF Society's website, A Brief History of the KH6 Duct Into The Pacific Northwest.



Steve McDonald, VE7SL, is a regular contributor to AmateurRadio.com and writes from British Columbia, Canada. Contact him at [email protected].

Field Day 2015 – Comprehensive Report

Most of the South Plainfield Amateur Radio Club showed up at Spring Lake Park at 10:00 AM or a little beforehand. There was enough pre-Field Day organization that we all pretty much knew what had to be done and what our roles were. Set up went well:

First - set up the antennas, and organize the tent - our "home" for the next 24+ hours.

South Plainfield Amateur Radio Club - NJ2SP - 3A - NNJ

Battery - all power provided was from solar charged batteries. No generators were used or fossil fuels burned to generate RF for the weekend.




Ron N2LCZ helping with the "tower" guys.

In addition to helping up with setting up antennas, Ron devised and built a network so that we could link the logging computers together. No small feat under the conditions we were operating under. N2LCZ is truly SPARC's resident Computer Expert (in addition to his yeoman's work as Club Secretary).


Notice the ominous looking sky - it was a harbinger of what was to come.


Dave KD2SFI (black t-shirt) putting together antennas for GOTA and VHF/UHF.

Dave Hackett KD2FSI, was our Field Day Committee Chairman this year. Dave was the "gasoline" in our Field Day "engine". Dave may be recently licensed, but he's already built up a good knowledge of what will work and what won't. He's got an enthusiasm for Amateur Radio and Field Day that is positively infectious. Dave is the kind of guy that makes you can't wait for the next operating event. If I was putting together a DXpedition to a very rare and exotic locale, Dave would be #1 on my short list of Hams who absolutely had to be part of the crew.


We had the tri-band beam set up on an extension ladder tower affair designed and constructed by our own Philip DeFort, KD2HPG.  Phil is a graduate of our Technician class from last Autumn. In addition to his mechanical contributions, he also added to our score by making some of his first on-the-air contacts as a Ham. He brought along his teen-aged son (also named Philip) who is now serious about getting his own ticket.


Here's a photo of Phil making some of his first contacts.

In addition to the tri-band beam, we brought back the EARCHI for another year. We had a ten meter dipole for GOTA and some VHF/UHF antennas built by Dave KD2DSI. We also had a W3EDP antenna up, which was built for the SSB station in anticipation that 20 Meters would probably close for the evening at some point.

We got through set up high and dry and were on the air promptly for the 2:00 PM EDT Field Day start. And that's when things started to go wrong. First, the winds kicked in and then it started raining buckets. It ended up being the soggiest Field Day that I can remember. In addition, it was pretty chilly all day. I was wearing a t-shirt with a sweat shirt on top, and resorted to adding a jacket as temperatures fell and humidity increased to 100%.  There were several times during the night when some of us went to our cars and just sat for about a half hour or so with the heaters on in order to get warm and dry out for a little bit.

Soon after the start, it became apparent that something was drastically wrong with the beam. The KX3 took a long time to find a match and even when it did, the antenna was not performing as expected. My Autek antenna analyzer showed the driven element was somehow resonant way out of band, so we switched the SSB transceiver over to the W3EDP and limped along for the weekend with that. Unfortunately, the W3EDP didn't perform much better, as I think there may have been a balun problem there. We would have been better off using Marv K2VHW's G5RV as we did last year, but it was already raining buckets and I wasn't about to risk pneumonia just to get another antenna up into the trees.

But even with the antenna mishaps, there were bright spots. Marc Sullivan W4MPS, who is a good QRP friend from North Carolina was in town to visit his daughter. He came by the Field Day site with his wife for a quick visit to say "Hello" before heading to his daughter's house. He came back by himself shortly after the starting gun sounded for a longer visit. And Marc's presence was truly a God-send because right around that time, the digital station was having some RFI problems which was causing their laptop to freeze. They needed some clamp on ferrites, which I had at home. Marc volunteered to keep our CW station busy while I was off fetching the ferrites and doing some other things.


Thank you,  Marc W4MPS for helping out!
 
In the photo of Marc W4MPS, the guy in background in the rain poncho is SPARC's own Mario KD2HPF. Undoubtedly due to his experience in Scouting, Mario was about the only one with proper foresight to come properly attired for the weekend.  Mario was also a graduate of our last Technician class held in Autumn, along with Phil KD2HPG. Mario was active in the Rookie Roundup and he was active again for Field Day. In addition to being a valuable part of the set up and tear down teams, Mario put in a lot of chair time at the 6 Meter station. He was our mainstay in keeping an eye open for any openings that may have occurred on that band. Mario had a Go Pro with him, and I think there's a video of him calling CQ on 6 Meters kicking around somewhere on the Web.

It was a long chilly night, but it was made bearable by visits from friends from our two neighboring clubs, the Electronic Testing Society of NJ, and the Raritan Valley Radio Club. So many showed up, that it's hard to remember them all and I beg pardon if I forget to mention any - but special thanks to:

Pete KD2ARB for the pizzas, Dave W2OIL and Dan KC2YRC for the home made brownies, the hot coffee and the help with tear down at the end. Marty WB2BEW donated the use of his pop up canopy, kept us company when it got lonely, and was just an all around morale boost. Marty is good people and it was good to have him with us. Same goes for Craig AC2FE, who came in the evening to keep us company for a while.  And Hank N2MU who was not only a friendly visitor, but also a critical thinker who helped us iron out some technical glitches. Again, if I left out any K2ETS or W2QW members, or any other visitors who showed up, I apologize, but my brain is still a little addled from the weekend.

On Sunday, around Noon, Mayor Matt Anesh and councilman Rob Bengivenga showed up at the site. We gave them the nickel tour and explained the operation and its purpose to them. The mayor was by last year, so he was familiar with Field Day, but Councilman Bengivenga was not. 


Yours truly talking antennas with Councilman Bengivenga. 


Marv K2VHW, SPARC President, explaining Field Day and the equipment with the Mayor and Councilman.

And wouldn't you know it, when the dignitaries appeared, the skies brightened up and the sun came out! I was joking around with Mayor Anesh that had we known that he was bringing better weather with him, we would have invited him over on Saturday!


And once again, South Plainfield's Finest parked one of their cruisers by our tent to serve as a little bit of an extra added deterrent against any possible mischief during our overnight stay. Police Chief Parker has been very accommodating towards SPARC, and as the SPPD takes on the role of OEM, we look forward to working with him. I didn't notice it, but fellow SPARC member, Tim Halloran AB2ZK pointed out to me the cruiser's official designation number. 


Car 73 - how appropriate!

So even though it was cold, wet and miserable, and we had antenna problems, and band conditions for Field Day weren't as good as they were in 2014, I think it's safe to say we all had a blast, and that SPARC is eagerly looking forward to Field Day 2016. We're going to remedy our problems and we'll be back, ready to once again take on whatever Mother Nature and Old Man Murphy dish out to us.


Drew W2OU working the digital station.

Drew Moore W2OU is our AC Log expert, fellow CERT member from Piscataway and a very valued member of SPARC.  Drew is a "Ham's Ham" and is a fun guy to be around and to just sit around and shoot the breeze with. Drew is also an ARRL official, so it's nice to have a little bit of the League with us all the time.


Tim AB2ZK and John AB2VE sharing a laugh during a lighter moment.

Tim AB2ZK was our "food guy" this year. Tim ran out Saturday night at 10:30 PM in the chill and pouring rain to bring us some hot sandwiches. He's always got a joke or quip up his sleeve exactly when one is needed. He was in South Plainfield's first CERT class and was a graduate of our first Technician licensing class back in 1995.  John AB2VE helped me set up the W3EDP and the EARCHI antenna. When I was getting a bit frustrated with the way the wind was blowing around the antenna lines I was launching, John kept me focused and on target. John is a veteran member of the South Plainfield Rescue Squad and is a very good friend to have.


W2LJ explaining the KX3 and the CW station to some visitors.
 
Lastly, two more SPARC members that I want to mention. Wayne Grennier N2LRE is our Vice-President. He's also our publicity guru who gets and keeps SPARC in the town's local publications. There are so many times that friends come up and say, "Hey Lar, I saw your picture in the Observer about that Amateur Radio thing you're involved with." Word of SPARC gets out because of Wayne. I wanted to snap a Field Day photo of him, but he was too busy flitting around with his camera, getting photos of the rest of us!
 
And our President, Marv K2VHW. Marv saw the need for a new Amateur Radio club in South Plainfield and did something about it. He's our navigator as we sail through uncharted waters. He has a good sense for what's good for the club and he's not afraid to try new things or to listen to a new opinion. SPARC is what it is because of Marv's leadership. We will forever be indebted to him. He keeps us engaged and active - and if a club is going to succeed, that's exactly what you need.

72 de Larry W2LJ
QRP - When you care to send the very least!






Larry Makoski, W2LJ, is a regular contributor to AmateurRadio.com and writes from New Jersey, USA. Contact him at [email protected].

Subscribe FREE to AmateurRadio.com's
Amateur Radio Newsletter

 
We never share your e-mail address.


Do you like to write?
Interesting project to share?
Helpful tips and ideas for other hams?

Submit an article and we will review it for publication on AmateurRadio.com!

Have a ham radio product or service?
Consider advertising on our site.

Are you a reporter covering ham radio?
Find ham radio experts for your story.

How to Set Up a Ham Radio Blog
Get started in less than 15 minutes!


  • Matt W1MST, Managing Editor