AmateurRadio.com

It has been a glorious day today. After lunch I set off for Tallentire Hill armed with the TH-205E and three antennas: a 2m telescopic quarter wave, a 45″ 2m 5/8 wave Black Whip telescopic from eBay seller jeepbangkok and the SOTA Beams MFD.

I set up the MFD in the vertical position strapped to a fence post and put out some calls. Despite my high elevation the 2m band was quiet and I only managed to raise “the usual suspects”. Richard MM1BHO/M heard me calling through the GB3DG repeater and we had a short QSO. Then Keith G0EMM heard me call on 145.500 MHz and was willing to spend a bit of time doing some antenna tests.

Prior to this I had heard a contact on the GB3CS repeater and had quickly swapped all three antennas to see what the difference was on receive. There was no noticeable difference between the MFD and the Black Whip but both were significantly superior to the 1/4 wave telescopic (which is itself an improvement over the short whips and “duckies” normally used with 2m handhelds.) However the signal was steady on the MFD whereas it varied depending on the position in which I was holding the TH-205E with the BNC mounted antenna. When using the MFD I was sitting on the ground so it was above my head and my body wasn’t interfering with reception. When using rig-mounted antennas it is best to stand up as an extra couple of feet above ground make a noticeable improvement. But it is also worth turning around and moving a short distance as the direction you are facing can make a big difference to signal strength.

Keith confirmed that there was no difference in my signal between the MFD and the 5/8 telescopic. I was 59 on both of them, whereas I was only 4 by 3 on the quarter wave. Keith also gave me my second unsolicited complimentary report on the TH-205E audio, saying it was “just like my voice.” I was using one of the cheap Kenwood speaker mikes which I bought on eBay originally for the TH-F7E.

We were then joined by Colin 2E0XSD who again said that I was the same strength, 59+ on both the MFD and the 5/8 wave. I was only 4 by 7 on the quarter wave.

After I finished the contact with Keith and Colin I tried some more calls. I was able to access the GB3CS repeater using the MFD and the 5/8 – when in the right position – but not with the quarter wave. Some repeaters I could hear but not access even with 3W, which is what the TH-205E appears to put out on “high power” with the 7.2V battery pack, but perhaps they don’t respond to 1750Hz tone-bursts.

When I bought the Black Whip a few weeks ago I put it on the antenna analyzer and got this SWR curve. I seem to remember that I had to collapse the topmost section to get the SWR null spot on 145.000 MHz but I don’t suppose it makes any difference in practise.

I think the Black Whip 5/8 telescopic is a superb antenna for 2m FM use and well worth the few pounds it costs, as long as you have a radio that can handle it. The base is sprung to absorb any shocks but even with the HT Saver SMA to BNC adapter I was a little uncomfortable using it on the tiny TH-F7E. The big old TH-205E has no such problems with a large antenna, although its lower power output with the battery pack I have is a slight disadvantage.

Is it worth carrying the MFD instead of the 5/8, which telescopes down to the same length as a quarter wave telescopic antenna? Well, if you are using a modern hand-held radio then the MFD’s coaxial connection will avoid putting undue strain on the SMA connector. You can secure the MFD to a fence post or stuff the support mast in your rucksack allowing you to operate sitting down and even let go of the radio when receiving. The MFD is also convertible to a horizontal dipole for SSB use. So it still has several benefits. But I expect I will be taking the Black Whip on most of my hilltop outings.

Single Operator All Band.

• Z35F (BALE) | 505 Qs | 40 Mults | 119,200 Points.
• UA4ALI | 614 Qs | 55 Qs | 16 Hrs | 96,360 Points.
• SQ6NTE | 149 Qs | 29 Mults | 26,564 Points.
• N2WN | 54 Qs | 14 Mults | 756 Points [TCG].

n = 4 scores submitted in this category.

Successful franchise building is an exercise in persistence, patience, imagination, and creativity. What lead to the success of World Wide DX, WPX, and International DX RadioSport events?

Contest on.

Just over a year ago I started Wainwrights On The Air (WOTA) as an adventure radio scheme to encourage people like myself to get out of the shack and up in the hills (or fells as they are known locally) of the English Lake District for a bit of fun with radio. You collect points by making contacts from the tops of the fells (which is called activating.) Armchair fellwalkers can also collect points by working stations on the tops of the fells (which is called chasing.) Certificates are awarded when you have made contacts from (or with) all of the fells in each of Alfred Wainwright’s seven Pictorial Guides, and for completing all 214 Wainwright fells.

WOTA has been more successful at getting other people out on the fells than me. To date, Phil G4OBK has been the most active WOTA activator and has already claimed a certificate for activating all of the fells in the Pictorial Guide to the Eastern Fells. He has stated that he intends to do all the Wainwrights within two years. Now he has started a blog to describe his progress towards completing this challenge.

Called “Wainwrights On The Air”, Phil’s blog has details of the routes taken as well as the people contacted from the fells. It has some great pictures, too, that really capture the flavour of this beautiful part of England.

If you like operating radio from the great outdoors, if you are interested in the English Lake District or if you are thinking about becoming a WOTA activator yourself, I think you’ll enjoy Phil’s Wainwrights On The Air blog.

The TH-205E transceiver was finally restored to full working order yesterday. After some thought I finally decided how to fit the 3A diode that was somewhat larger than the recommended part which was unobtainable. I extended the left-over wires from the old fuse using thin wire taken from the leads of a small capacitor. I then shortened to a few millimetres and tinned the leads of the new diode. I wound the thin wires on to the stub leads of the diode and then soldered them whilst using tweezers as a heat sink on the thin wire to prevent the other end coming unsoldered.

The radio now works off its new battery. It made its first QSO with Derek G1GDB via the GB3LA repeater, and received complimentary reports on the audio. I even took it along to the Workington Radio Club meeting in case there was a “largest 2m hand-held” competition!

I also finished up the drop-in battery charger which I built using this circuit using an LM317T voltage regulator. It is simple to make and has an LED to show that it is charging. The hardest part was cutting the rectangular hole in the plastic project box. It’s best not to look too closely or you can see that the edges are not perfectly straight.

This picture shows an internal view of the charger. It doesn’t show the contacts for the charging tabs on the battery which were made from a paperclip. The sleeve that holds the radio or battery in position was cut from the cardboard box that my UNI-T Oscilloscope Digital Multimeter came in, and is super-glued to Veropins to hold it in place. Hopefully the heat sink for the LM317T will be adequate – the battery hasn’t lost the charge I gave it using the shack power supply so I haven’t yet had the chance to test it for a full 15 hours.

XR0Y videoblog – part 8 from SQ8X on Vimeo.

Believe in your signal.

The Beaconworld website will be closing down in May. If you’ve never heard of it before, neither had I until I read about it in M0XPD’s blog. But having visited the site, it seems to be an excellent and comprehensive resource for anyone interested in beacon DXing. It’s a shame that it will disappear even though it is being closed for reasons that I can understand.

Have a look while it’s still here. Perhaps someone will step in and offer to take over the site and carry it on, or at least to preserve the pages as they are.

I seem to be collecting VHF handhelds at the moment. This is the Motorola Radius GP300 I bought for £1 at the Blackpool radio exhibition yesterday. The seller had quite a number of shiny new-looking commercial handhelds in a heap on the table, all without batteries, which were being sold for £1 each. He told me they were all UHF. Most were Midland radios, but there was this one Motorola which in the end I decided to get because I thought it might be easier to find information about it. I should have got one of the Midlands as well, after all, it was only a quid!

Today I took a closer look at what I had bought, and tried to find out something about it from the internet. From the model number I was able to find out the capabilities of the radio and I actually have a VHF handheld which can cover 144 – 176MHz in 12.5kHz steps, 8 programmed channels with 5W output. I can’t test if it works because I don’t have an adapter for the strange type of antenna socket, but Motorola to BNC adapters are available on eBay. However for the radio to be any use I will need to program it with some 2m band frequencies.

There is information on the web showing how to build a programming interface, but you can actually buy one ready made from Hong Kong for little more than the cost of the parts. The difficulty appears to be getting hold of the all-important programming software. Apparently it was very expensive and Motorola doesn’t turn a blind eye to free sharing of it among the amateur community so I was unable to find any download link.

None of the sites that give information about programming these radios provide any help about how to get hold of the software and they are obviously fed up with being asked about it. So there probably isn’t much that I am going to be able to do with this radio. A pity, as it seems to be well regarded judging by the reviews on eHam, presumably posted by users who got them from dealers pre-programmed with the channels of their choice.