AmateurRadio.com

Here’s an email from my good friend and cohort in the Central Florida QRP Group. Jim wanted to share his latest mods for the Rockmites and some thoughts on the NEScaf filter. I think you will enjoy his notes too …

Kelly,

I thought I would bring you up to date on my latest project. I just finished a Small Wonder 20+ and used it on the Flight of the Bumblebees. I found my earbuds a little weak on audio output and the IF bandwidth of the SW20+ a bit wide for my liking. I read the specifications on the NEScaf filter offered by the New England QRP group and decided that that would be the best solution to my problem and be usable on other radios as well. I ordered, built and installed the NEScaf board in a TenTec TG-24 enclosure. I tried it on the SW20 and it sounded like a viable solution.

The Rockmite and NEScaf filter in Ten Tec Enclosures

I also have a 40 Meter Rockmite in a TG-24 enclosure and decided I would see how well the RM/NEScaf combination sounded. The Rockmite, of course, uses a DC receiver and the bandwidth is determined by the upper response of your ears… My RM sounds like about 40 khz wide, hears the whole band for me as my response is in the upper tens of kHz. Yes, I know, at my age 69 it shouldn’t be but is. Been tested. At any rate suddenly the Rockmite bandwidth is manageable. I had some audio artifacts, whistles and the RM sidetone would drive the NEScaf into cutoff which only a power cycle would clear. I googled the problem and Charlie KE2SP advised lowering the NEScaf input Z with a 10 to 47 ohm input load. I installed a 27 ohm resistor on the input connector and suddenly all artifacts, whistles and sidetone problems disappeared. WOW, the RM is really sounding great! Except the RX/TX was very low. I measured it at 500 cycles and the NEScaf would not tune down that low…

Closer Look at the Finished Rockmite and NEScaf

After considering several approaches to the problem and considering that the RM crystals don’t oscillate on exactly the QRP frequencies, I settled on completely revamping the RX/TX method used in the RM. Using the RM40 as a test bed, I removed D5, D6, R9 and R10. I purchased 2 Murata trimmers( TZ03 Series) from Skycraft, our local Surplus emporium, and installed them in the holes for D6 and D5, R9 combination of holes. I had to cut a small run on the right side (antenna connector side) to isolate that pad from Vcc and jumper to two trimmers together… I also had to drill out the pads to accept the trimmer leads. The Fet Q2 does a great job in switching to second trimmer in and out for the offset. The alignment was not difficult but I recommend using a freq counter connected thru a times 10 scope probe to the physical top of R5 (base of Q5). Don’t have to key the Tx to see the freq… I set the trimmer in the D6 position for the higher freq (7.030750 Mhz) and the other trimmer for the lower frequency (7.030000 Mhz. The trimmers I use are available at Digikey. I used the Red colored model (4.2 to 20pf, N750) but the Blue colored (2.7 to 10pf, NPO) might have been a better choice. These guys are Digikey p/n 490-1971-ND and are $0.43 each… I also changed the RM40 volume control from an audio control (1 Megohm) to a RF front end attenuator control (1.5 kohm) and there is a noticeable improvement in the overload and broadcaster breakthru problem. I strongly recommend these changes. If you can build the RM you can certainly modify it… If you break it, build another… I plan to make the same modification to my RM80. (CLICK THE THUMBNAILS for larger view)

Rockmite Mode Closeup 1

Rockmite another closeup

The Inner Workings of the NEScaf and Rockmite

How did it work? Well, the RM/Nescaf stack is now a real radio not just a toy. I worked WD8MHT Raul in Waynesville, NC one morning this week and we had a great conversation. He was 569 to me and I was 439 to him. His TS570 was working hard but copied me no problem. The amazing thing for me was that there was a really strong signal at 700 cycles and Raul was about 200 cycles higher. I tuned the Nescaf center freq on Raul and sharpened the bandpass and turned up the volume and he was armchair copy the entire QSO… WOW, not a struggle… I have since used the NEScaf on my SW20+ and yes, it works great…

I have attached a couple of pictures of the stack and the innards of the RM for reference. The switch on the front is for a future expansion.

72

Jim

K4AHO

Now into the third week of my sabbatical, I am surprised how much I want to get out and operate my QRP portable gear. Guess I have deprived myself over the years of being a confirmed workaholic and avoiding time off, vacations, and time for my favorite hobby.

Grrrrr! The Polar Bears Are On The Loose!

This should be a good weekend for QRP portable. The Polar Bear QRP Group will be out for another Polar Bear Summer Picnic Event and Polar Bears from Spain to the West Coast of the US will be out looking for BSO’s. Grrrrr! I am PB #173 and we’re over 200 members now. With the new Twitter and APRS connections to QRPSPOTS.COM which also point to the excellent spotting site of K3UK with a section for FISTS/QRP Ops to spot and sked one another, there are plenty of ways to use technology to help find each other. Add in a few other contests and state QSO parties, and there should be some buzzing going on this weekend. Makes me wonder when the FOBB results will be announced! Buzzzz Buzzzzz

I’ll be out and if all goes well I will be field testing a new C Pole antenna based on the suggestion I received from Neil W0LVZ. I added some switchable capacitance to my BLT+ and have rewound the main toroid to see if I can push the range a bit more with it so will have a delta loop and probably my W3EDP in the air too. I love playing with antennas and am still amazed when the ones I build actually make contacts!

Give a listen for me on the QRP watering holes on 40m, 30m and 20m Saturday morning. I’ll be self spotting on QRPSPOTS and the K3UK sites to make it easier for you to find me. Let me know how my newest antenna is workin’.

72,

Kelly K4UPG

PB #173

After last week’s plea for antenna ideas for my antenna restricted condo, I received a good number of comments both on and off blog. Thanks for those… great food for thought. That is why I enjoy our QRP community. We don’t hesitate to share ideas with one another.

This morning as I took my daily walk around the lake, I met our condo association president. He graciously is allowing me to sink a pipe that will serve as a base to set up my Jackite poles in the backyard. I will be able to pop a cap on the top and keep the dirt and water out and just slide my fiberglass poles into the mount and be on the air in no time. YAHOO… that is a pretty good solution for now.

C Pole Antenna by W0VLZ

But being the antenna tweak that I am, I continue to look for the best alternatives I can find. I’ve started to put together the parts for the C Pole antenna that Niel W0VLZ pointed out to me. He has a fine site with lots of good QRP info too.

So, do you have another idea that can top that one? Or maybe you have a thought for what kind of vertical setup I might use with the new mount?

I’m standing by for my next project assignment.

72,

Kelly K4UPG

We purchased our condo before I got back into ham radio. Like most in Orlando, we have antenna restrictions. I can put up portable or temporary antennas but cannot mount anything to the building permanently. I’d love to be able to get on the air without all the hassles of dragging gear to the porch, setting up an antenna and then tearing it all down again. It takes so much time to setup and tear down that it turns a few minutes of operating into a long process.

Here’s the layout I have to work with at the QTH…

The front yard view… I am next door down from the blue car

Preferred antenna site is the backyard

The buildings run north and south and these photos are shot facing due north. My condo is ground floor, second from the south end of the building. Yes, that is a big electrical transformer box and a major underground feeder line runs to it from the north.

I’ve used my Buddistick with some success but it doesn’t like being so close to the buildings and the swr is higher than when it is out in the open. I also have run a doublet inverted vee fed with twinlead but the north south orientation is not very favorable from my Florida QTH and sends most of my rf into the two buildings. My W3EDP works fairly well as an inverted L with my 20′ Jackite pole and I’ve used end fed halfwaves as slopers and inverted vees but again the directivity is not favorably oriented. I have a 3 foot magnetic loop propped against the wall but it is not working as well as I’d like yet. (i.e. the outdoor antennas work LOTS better so far)

Thought I’d ask ya’ll for some input.

Any outrageous ideas or thoughts for  me? Send me a comment and let me know.

Thanks in advance for your thoughts.

I still think the tin foil does the magic!

After years of neglect, this analog era ham is willing to admit I only understand a bit about digital electronics. (Yep! Pun intended.) Well into the second week of my sabbatical leave, I have begun to plot out a course of study to get up to speed on the state of the art that I have so long neglected. Should be fun. There seems to be a good bit of open source help online these days and I have my trusty ARRL Handbook, Extra Class study guide, Antenna Handbook and assortment of other aids.

Any suggestions from the veteran techies out there will be greatly appreciated.

I am a learn by doing/hands-on sort of guy and find deep theory puts me into a semi-catatonic state after a few minutes.  For me, it’s a whole lot more fun to take a stab at things and find out if they smoke, and it also makes a lot more sense when I can dink and tweak and see what that actually does. But since that is a bit expensive, perhaps I should learn how to use software like spice to do simulations? Any recommendations for how to learn this software?

Another area of toe dipping will be learning to do antenna modeling. For years I’ve looked at those charts and made little sense out of them. HA… I like to throw wire out and see what happens, but in the summer heat, maybe it is wiser to do a bit of modeling from my air conditioned den?

Thanks WX7S– Your site looks AWESOME for learning this stuff!

I’ll try to share some of the learning curve, but would love to hear from some of you that have gone before. Shortcuts are nice. WX7S your site looks like a great place for me to start! Thanks for the effort it takes to do that.

This weekend (Sat 14 Aug 2010) the Central Florida QRP Group will gather for breakfast at 0730 (Denny’s in Sanford, FL) and off to Sylvan Lake Park in Sanford, FL at 0900 EDT to operate. If you like cw and qrp or are just plain curious… come join us!

What is it about low power operators that binds us together? I’ve been reflecting on that a bit lately.

As a student of anthropology and culture, I see a bit of a tribal influence among the amateur radio ops of the world. We tend to cluster into tribes based upon our modes of operation and other specialized pursuits like contesting, fox hunting, award seekers, etc. Each tribe has its own special characteristics, culture, jargon and social structure.

What I enjoy most about the QRP tribe is that the Elmer spirit is still very much alive and well. Although we all are a bit competitive and like to think we have a line on the best way to do QRP, there is a healthy amount of sharing of information, expertise and even hardware. Groups like Adventure Radio Society, NAQCC, Flying Pigs, Polar Bears, AZ Scorpions, NE QRP, North Georgia, 4 States, etc breed healthy competition and provide us with sources of information and expert assistance when needed. I sure am enjoying getting to know, both on air and in person, some of the people that make these groups work.

My recent connection with Diz W8DIZ while operating the FOBB, prompted me to go back and read the history of the Flying Pigs and to read through the archives of the Bacon Bits Newsletter. There is real gold and a wealth of interesting info that’s been recorded and made available freely. Other clubs have the same heritage. I say a BIG THANK YOU to all the QRP groups for sharing their experience and stories. It makes me feel proud to be part of the tribe!

What about you? What do you enjoy about QRP? Leave a comment and share your thoughts and story.

Various QRP related email reflectors and lists are full of chatter about the Flight Of the BumbleBees (FOBB). Comments about the CW being too fast and the weather being too hot at this time of year make it sound like a broken event. IMHO it is far from being broken! It is probably the premier QRP event of the year. And I say, if it ain’t broke… yep, you guessed it, don’t fix it.

Sunday the bands were full of QRP ops, both home based and portable, so the activity really did make a BUZZ despite band conditions that have not been all that helpful to hf qrp contacts.  The weather was HOT, but hey, find some shade, altitude or water and go for it. Historically this is the time of year for this event and as others have commented, it keeps our activity up during the summer time when vacations and mowing the grass take their toll on ham radio activity.

As far as fast cw, I’m not fast (not even close hi hi), but it sure is fun listening to the buzz on the bands rather than QRN and a high noise level with only a few weak signals. Certainly I am not a hard core contester. My cw skills are still in need of practice, but isn’t that what events like this provide? I often have to listen multiple times to get the callsign and info but that repetition and practice pushes my speed and confidence level up every time I try. After listening to a fast op several times I have the info I need and then I jump in and have fun making a contact at speeds faster than my comfort zone. Most of us slow guys can send faster than we can receive, right? Come on in, the water is fine, and FUN!

My XYL, Connie and I drove over to Honeymoon Island State Park on the Gulf Coast in Dunedin, Florida. This is a very pretty beach, not overly crowded most of the time and has been one of the top rated beaches in the US for several years. The weather cooperated, there was no sign of the BP oil spill that has run so many tourists to other locations, and we snagged a primo spot to operate right next to the water.The only negative, if you call it that, was that the view was sometimes distracting, but sure was enjoyable.

K4UPG Distracting View from my FOBB 10 Site

K4UPG Honeymoon Island FOBB Site July 2010

My trusty Sierra and Buddistick provided plenty of action so I never switched over to my mini-bac Delta Loop backup antenna. I also stuck to 20m the whole contest since 40m has been in such poor condition here in Florida lately.

One of the great things about these events is the leveling of the playing field. It is fun to contact the guys that write the articles, create the websites and design the equipment that we use for our hobby. My score was modest at 26 QSO’s, 18 Bumblebees and 17 states and provinces but it was one fantastic day of activity for me! Being able to connect with the big guns of QRP was a thrill too!

W8DIZ Stops By to say Hello to K4UPG

K4UPG search and pounce FOBB 10

For me, one of the highlights was when W8DIZ rode over to meet me as I was setting up my site. Diz lives about 3.5 miles from Honeymoon island and is a regular bicycle visitor of this great beach location. I’ve been a customer of his toroid and kit business and have benefited from the info he has shared, not to mention being one of the movers and shakers of the Famous Flying Pigs QRP group. Diz I was honored that you took time out from a busy family day to swing by and say HI! Thanks for the help getting our screen house up too!

Thanks to Adventure Radio Society and the guys that put this event on for all of us. We appreciate the effort it takes and you deserve the very best of 73′s from all of us.

72,

Kelly K4UPG  BB #10