Posts Tagged ‘Cyclone 40’

David Cripe’s NM0S Cyclone 40 Meter Transceiver kit

Readers, check out the Cyclone 40 in this release:

A new kit from the Four State QRP Group and David Cripe (NM0S)

NM0S's Cylcone 40M QRP transceiver.  Look for it at Four Days in May!

NM0S’s Cylcone 40M QRP transceiver. Look for it at Four Days in May!

Arising from Dave’s entry in QRP ARCI’s 72 Part Challenge Design Contest in 2010, the Cyclone 40 is an enhanced version of the original design. The transceiver designed for the design contest had 72 total parts, performed well, and won honorable mention. This improved version has less than 100 components and even better performance! The kit features all through hole parts and easy assembly. The receiver is a superhet design with very good sensitivity and selectivity, and tunes the entire 125 kHZ CW segment of the 40M Band – and does so at a comfortable tuning rate. A frequency readout is included so you know where you are at all times.

This is a complete kit, including the enclosure. A high quality board package includes the pc board, front and back panels, the sides, and top and bottom all of which make up the enclosure. The control and jack labels are silk screened in white letters and vividly contrast with the black solder mask, and the holes for the connectors and controls are pre-drilled. The ends are “dovetailed” together making a very rugged, easy to build, and attractive enclosure.

Features and Specifications

General

  • Enclosure: A very nice predrilled and silkscreened enclosure is included. It’s easy to assemble and looks great.
  • Ergonomics: Smooth solid tuning, a quiet receiver with QSK and well behaved AGC. Nicely laid out front and rear panels.
  • VFO: The VFO is a simple PTO design, is very stable, and also quite easy to build
  • Sidetone: Included!
  • AGC: Audio derived, fast and smooth.
  • Frequency Range: 7.000 – 7.125 typical.
  • Tuning Speed: 10kHz/knob turn typical.
  • Stability: 300 HZ the first 5 min after power up, less than 10 HZ/hour after that.
  • QSK: Fantastic QSK! Full Break in, excellent muting, really fast!
  • All Through Hole Parts There are NO SMT parts in this kit, and only three easy to wind toroids.
  • Dimensions: 4.4 x 3.6 x 1.9″
  • Power Connector: 2.5×5.5mm coaxial, center positive. Should be fused at 1A, fast blow at PS
  • Antenna connector: BNC

Receiver

  • Configuration: Superheterodyne, 11 MHZ IF, 4 Crystal IF Filter.
  • Sensitivity: MDS (Minimum Discernable Signal) -125, Typical, below the normal 40M band noise level.
  • Selectivity: Four crystal, 500 HZ IF filter
  • IMD3: 90 dB typical, better than most commercial gear!
  • IP3: +10 dBm typical – another very good number
  • Frequency Readout: 3 or 4 digit CW, 1 kHz or 100 Hz resolution (user selectable), developed by Adrian Hill, KCØYOI.
  • Band Edge Marker: A band edge marker is heard at 7.001 MHZ
  • Headphone Jack: 1/8″ stereo, standard earbud/Walkman® headphone compatible
  • DC Current consumption: 30 ma typical at 13.6 VDC.

Transmitter

  • Configuration: Stable, Wide Range VFO (PTO design), Efficient Class E Final.
  • Spectral Purity: All harmonics and spurs less than 50dB below the carrier.
  • Output Power: approximately 4W into 50 ohms
  • DC Current consumption: 500ma typical at 13.6 VDC Will operate down to 9v DC.
  • Key Jack: 1/8″ stereo, grounded shell, switching the tip keys TX. Contacts accessible for an internal add-on keyer

Kits should be available at QRP ARCI’s Four Days in May conference at Dayton, and will be for sale on the Four State QRP Group’s web site approximately May 20th. The final price hasn’t been determined yet but should be less than $100 plus shipping.


Subscribe FREE to AmateurRadio.com's
Amateur Radio Newsletter

 
We never share your e-mail address.


Do you like to write?
Interesting project to share?
Helpful tips and ideas for other hams?

Submit an article and we will review it for publication on AmateurRadio.com!

Have a ham radio product or service?
Consider advertising on our site.

Are you a reporter covering ham radio?
Find ham radio experts for your story.

How to Set Up a Ham Radio Blog
Get started in less than 15 minutes!


  • Matt W1MST, Managing Editor




Sign up for our free
Amateur Radio Newsletter

Enter your e-mail address: