Amateur Radio Weekly is curated by Cale Mooth K4HCK. Sign up free to receive ham radio's most relevant news, projects, technology and events by e-mail each week at http://www.hamweekly.com.

Temperatures this morning were still cool(-10c) when I got up but the sun was starting to shine nice through the tree’s.

I was looking forward to the RaDAR event as well as the regular gathering of HFPack, HFNow and RaDAR gang that will congregate on or near 18157.5

I once again donned my favorite rig, the PRC-104, with the Chameleon Whip, a 10’7″ counterpoise and headed out around the property.

Once on 17 meters the first I heard was Greg N4KGL who was QRP with the KX3, he was maybe a 2×2 but was unable to hear me call him. I called a number of times but no joy. I then heard my friend Budd W 3 Fast Freddie calling and he worked Greg, I then called as well and when Budd was clear with N4KGL he called me and we were able to have a 2 way 5×9 exchange on the band. Budd then asked if anyone else was hearing me and Warren KD4Z in GA. came back to me with a great report, so we exchanged reports and had a good qso, Warren then worked Tom G0SBW who was very weak to me, I asked Warren to pass along to Tom that I said hello and that he was just audible here.

I then came in the house for a minute and noted that Paul W0RW was portable with his Green Radio on 18.088, so I tuned the PRC-104 down to 18.088 and put the leg key on and worked Paul, we were both 599 reports so great signals on 17 meters.

After about an hour outside I was happy with the contacts I made and the propagation conditions as well as teh weather outside as I was able to operate with no gloves on again today.

So thanks to Budd, Warren, Paul and of course the RaDAR gang for being on the air and playing radio and going portable, thus the Rapid Deployment Amateur Radio group.

Next weekend, April 3rd and 4th (0000z-2359z) will be the 24 Hr. RaDAR event and I will be out portable for that one as well operating SSB,CW and digital modes.

RaDAR Information Below:

1. Aim
The RaDAR “Challenge” is a unique event aimed at promoting the use of Rapidly Deployable Amateur Radio stations. This challenge is for all licensed radio amateurs not limited to South Africa. A RaDAR operator can take part in any of the three defined categories (see point 7) which may be changed at any time during the challenge. The
points system is so structured as to encourage portable RaDAR operations, especially moveable RaDAR stations. Moveable RaDAR stations rely on fixed and portable stations as a point of contact using channelised frequencies. “Search and pounce” techniques are also allowed.

2. Date and Time
From 00:00 UTC to 23:59 UTC on Saturday 4 April 2015 and from 00:00 UTC to 23:59 UTC on Saturday 7 November 2015 – 24 hours will give equal opportunity to the international community of RaDAR operators. RaDAR operators can define their own operating time schedule or remain active for the full 24 hours.

3. Bands and Modes
All amateur bands are allowed including cross band contacts via amateur radio satellites.
Modes – CW, SSB, AM, FM or any legal digital mode. QSOs via terrestrial repeaters will NOT be allowed.

4. Suggested HF calling frequencies
See http://zs6bne.wordpress.com/2013/03/06/radar-calling-frequencies/ for the latest international list of frequencies. The WARC bands can be used considering this is a RaDAR Challenge and not a contest as such. It provides better opportunities for Ra-
DAR contacts during difficult propagation conditions.
Recommended digital modes frequencies – Refer to the South African Radio League Contest Manual, General Rule 15.

5. Exchange
The RaDAR challenge requires more than a minimalistic information exchange. Accurate information exchange is considered more important than a large QSO count.
Call sign, name, RS(T) report, QTH and grid locator. Note the grid locator can change as RaDAR operators are allowed to move position at any time. The grid locator of six characters is acceptable but should preferably be accurate to 10 characters for higher
position accuracy. Smartphone applications are generally used to establish more than a 6-character grid locator. If working non-participating stations, call sign, name, RST and QTH is acceptable.

6. Scoring
1 point per QSO.
Individual QSOs – per mode, per band, per satellite, per call sign.
If the moving RaDAR station has moved the required distance (see point 7) contact can be made with a previously worked station, again.

7. Categories and multipliers
The following multipliers are applicable to determine the final score. If category/mode of transport changes were made during the challenge, than calculate accordingly.

X 1 – RaDAR Fixed station (At home or in another building)
X 2 – RaDAR Field station (Portable – away from home)
X 3 – Moving RaDAR station – See modes of transport below.

Modes of transport and required movement distances (moving RaDAR stations only)
Vehicles, motorcycles and motorboats etc. (Motorised transport) – 6 km
Bicycles – 2 km
On foot and paddle canoes – 1 km
Wheelchairs – 500 m
Aeronautical mobile stations are considered moving stations and can communicate at any convenient time.
Note: Moving RaDAR stations can move at any time but are required to move to the next destination after five contacts have been made from the present location. The move needs to cover the required distance before further contacts are allowed to be made. This requirement tests the ability to rapidly re-deploy your amateur radio field station.

9. Bonus points (All categories)
Five (5) points (The equivalent of five QSOs) for a minimum of one satellite or any digital modes QSO involving a computer, smartphone or digital modes device. (For clarity thereafter 1 point per Satellite / Digital modes QSO).
Five (5) points for the first successful same continent RaDAR to RaDAR QSO (As may be confirmed by the extensive information exchange.
Five (5) points for the first intercontinental (DX) QSO
Ten (10) points for the first successful inter continental (DX) RaDAR to RaDAR QSO (As may be confirmed by the extensive information exchange).

10. Log Sheets
Log sheets must be submitted by 14 April 2015 and 17 November 2015 and sent by e-mail to [email protected].

See https://zs6bne.files.wordpress.com/2015/03/11046905_10152762072212759_727315224761083499_n.jpg for a log sheet specifically designed for the 2015 RaDAR contest.
Note: A photo of the station (JPG format) MUST accompany every log entry. A photo is required for each new location that moveable stations visit. These photos are used to promote amateur radio and the RaDAR concept showing where amateur radio can be used to communicate from and in the many different ways.

 

 

 

 

Have a great weekend one and all and a good week coming up.

 

72/73

Fred

VE3FAL

The “Ice Man”

 

Fred Lesnick, VE3FAL, is a regular contributor to AmateurRadio.com and writes from Thunder Bay Ontario, Canada. Contact him at [email protected].

Thanks to a recent posting in the Yahoo ParasetBuilders Group, I have a new-found respect for my small collection of prewar crystals! If you've ever wondered how a rough chunk of quartz gets transformed into an accurate frequency-generating device, this 'cinema-style' documentary shows exactly how it was done ... truly an amazingly complex, yet delicate, labor-intensive process.



After viewing the documentary, I can't help but wonder what later health effects some of these workers may have undergone after seeing them handling some nasty-looking chemicals and working directly beside desktop X-ray machines. If you've used old WW2 crystals before, I think you'll enjoy seeing how much work went into their production.
Steve McDonald, VE7SL, is a regular contributor to AmateurRadio.com and writes from British Columbia, Canada. Contact him at [email protected].

I didn’t pay much attention to the GT-1 because I assumed it was just old wine in a new bottle. Time to rectify this, due to popular demand.

We all know the Baofeng BF-666S / BF-777S / BF-888S radios: 16 UHF channels, no display, low power output, a receiver which can be overloaded by snapping your fingers, but they are dirt cheap. The GT-1, co-developed by SainSonic, promises to improve on this concept by adding FM radio, a higher capacity battery and higher power output.

Look & feel
When it comes to looks, the GT-1 looks a bit more modern than its predecessors. The radio is slightly taller and less deep. All in all the GT-1 looks and feels nice. The basic concept didn’t change: 16 programmable UHF channels between 400 MHz and 470 MHz, scramble (voice inversion), a on/off/volume pot, a 16-step rotary encoder and a flashlight. Apart from emitting a steady beam of light the flashlight now offers an ‘SOS- mode: three short, three long and three short pulses.

You can order the radio with side keys in different colors: yellow, orange or green. The (of reasonable quality) manual comes in three languages: English, French and German. Nice touch.

Battery
According to the specs printed on the battery the nominal voltage is 7.4 Volts @ 1800 mAh, the same capacity as the UV-5R battery.  Such a capacity would be in line with the higher power output promised on the radio label: a solid 5 Watts instead of ‘less or equal to 5 Watts’ printed on a BF-888S (which proved to be 2 Watts only).

The first hint of something being terribly wrong was the weight of the battery. It felt so light that I was afraid that it might end up at the other end of the living room if I had a nasty cough. Time to to take a closer look at things. Let’s take a look at the weight first as more cells always translates into a heavier battery.  The amount of plastic used plays a role too, of course. So while this is not a 100% reliable method, it does give you an indication.

Battery weight comparison
Pofung GT-1: 47 grams
Baofeng BF-666S: 54 grams
Baofeng UV-5R: 80 grams
Anytone NSTIG-8R: 96 grams

As you can see the weight of the GT-1 and BF-666S batteries are close. The UV-5R and NSTIG-8R batteries are too, both proven to be 7.4 Volts @ 1800 mAh. The GT-1 battery seems just too light to be in the same 7.4 Volts / 1800 mAh league.

I took my multimeter and checked the GT-1 battery. Not to my surprise it only measured 4.0 Volts (freshly charged), so the nominal voltage is 3.7 Volts only, just like the BF-666S battery. The capacity will likely be the same too, somewhere between 1000 mAh and 1500 mAh.

Transmitter
After finding out that the battery might even be inferior to the one supplied with its predecessor I didn’t expect the GT-1 to be able to reach 5 Watts output at all. That proved to be correct. Two samples measured the same: between 1.5 – 2 Watts, depending on the frequency.

TX Audio
A bit brighter and slightly louder than my BF series, which is a plus.

Phase noise and harmonics
Less phase noise than the BF series. There are some unusual peaks visible, but nothing scary.

Receiver
At -126 dBm the GT-1 is sensitive enough, but that won’t help you much. It doesn’t take much of an out-of-band signal to make the radio as deaf as a post. Even the local repeater can’t be received in my city center; only if I’m about 3 kilometers away from the center the receiver comes to life.

FM Radio
By holding the upper side key while switching on the radio, the GT-1 will switch to FM radio, something the BF series don’t offer. There doesn’t appear to be a way to tune to a preferred station though; it randomly tunes into stations it finds. This makes the feature of limited use.

Edit: pressing the upper side key shortly will make the radio switch from station to station. Some in-house interference made the system fail when I tested it. The interference caused the scan to stop when encountering these false positives.

RX Audio
A bit raw, just like with the BF series, but more tinny. Audio distorts quickly if you crank up the volume.

Software
The GT-1 can be programmed with the same software developed for the BF series. CHIRP works too, but lacks a few options such as switching on scramble. Changing power output from ‘High’ to ‘Low’ in the software still doesn’t work; the radio just ignores that setting.

The verdict
After being confronted with all the lies surrounding the Pofung GT-1 there’s no way I can justify a diplomatic way of saying things. The GT-1 is just old wine in a new bottle, the battery voltage / capacity is one big lie and so is the promised power output.

The receiver is still disappointing unless you live in the proverbial ‘middle of nowhere’. To make matters worse the GT-1 is more expensive than a Baofeng BF-666S / BF-777S / BF-888S.

In short: don’t buy one unless you’re a notorious masochist. Go for a UV-5R instead or, if you like/need this particular concept, buy the superior Anytone ANILE-8R.

Hans, PD0AC, is a regular contributor to AmateurRadio.com and writes from Almere, The Netherlands. Contact him at [email protected].

I didn’t pay much attention to the GT-1 because I assumed it was just old wine in a new bottle. Time to rectify this, due to popular demand.

We all know the Baofeng BF-666S / BF-777S / BF-888S radios: 16 UHF channels, no display, low power output, a receiver which can be overloaded by snapping your fingers, but they are dirt cheap. The GT-1, co-developed by SainSonic, promises to improve on this concept by adding FM radio, a higher capacity battery and higher power output.

Look & feel
When it comes to looks, the GT-1 looks a bit more modern than its predecessors. The radio is slightly taller and less deep. All in all the GT-1 looks and feels nice. The basic concept didn’t change: 16 programmable UHF channels between 400 MHz and 470 MHz, scramble (voice inversion), a on/off/volume pot, a 16-step rotary encoder and a flashlight. Apart from emitting a steady beam of light the flashlight now offers an ‘SOS- mode: three short, three long and three short pulses.

You can order the radio with side keys in different colors: yellow, orange or green. The (of reasonable quality) manual comes in three languages: English, French and German. Nice touch.

Battery
According to the specs printed on the battery the nominal voltage is 7.4 Volts @ 1800 mAh, the same capacity as the UV-5R battery.  Such a capacity would be in line with the higher power output promised on the radio label: a solid 5 Watts instead of ‘less or equal to 5 Watts’ printed on a BF-888S (which proved to be 2 Watts only).

The first hint of something being terribly wrong was the weight of the battery. It felt so light that I was afraid that it might end up at the other end of the living room if I had a nasty cough. Time to to take a closer look at things. Let’s take a look at the weight first as more cells always translates into a heavier battery.  The amount of plastic used plays a role too, of course. So while this is not a 100% reliable method, it does give you an indication.

Battery weight comparison
Pofung GT-1: 47 grams
Baofeng BF-666S: 54 grams
Baofeng UV-5R: 80 grams
Anytone NSTIG-8R: 96 grams

As you can see the weight of the GT-1 and BF-666S batteries are close. The UV-5R and NSTIG-8R batteries are too, both proven to be 7.4 Volts @ 1800 mAh. The GT-1 battery seems just too light to be in the same 7.4 Volts / 1800 mAh league.

I took my multimeter and checked the GT-1 battery. Not to my surprise it only measured 4.0 Volts (freshly charged), so the nominal voltage is 3.7 Volts only, just like the BF-666S battery. The capacity will likely be the same too, somewhere between 1000 mAh and 1500 mAh.

Transmitter
After finding out that the battery might even be inferior to the one supplied with its predecessor I didn’t expect the GT-1 to be able to reach 5 Watts output at all. That proved to be correct. Two samples measured the same: between 1.5 – 2 Watts, depending on the frequency.

TX Audio
A bit brighter and slightly louder than my BF series, which is a plus.

Phase noise and harmonics
Less phase noise than the BF series. There are some unusual peaks visible, but nothing scary.

Receiver
At -126 dBm the GT-1 is sensitive enough, but that won’t help you much. It doesn’t take much of an out-of-band signal to make the radio as deaf as a post. Even the local repeater can’t be received in my city center; only if I’m about 3 kilometers away from the center the receiver comes to life.

FM Radio
By holding the upper side key while switching on the radio, the GT-1 will switch to FM radio, something the BF series don’t offer. There doesn’t appear to to be a way to tune to a preferred station though; it randomly tunes into stations it finds. This makes the feature of limited use.

RX Audio
A bit raw, just like with the BF series, but more tinny. Audio distorts quickly if you crank up the volume.

Software
The GT-1 can be programmed with the same software developed for the BF series. CHIRP works too, but lacks a few options such as switching on scramble. Changing power output from ‘High’ to ‘Low’ in the software still doesn’t work; the radio just ignores that setting.

The verdict
After being confronted with all the lies surrounding the Pofung GT-1 there’s no way I can justify a diplomatic way of saying things. The GT-1 is just old wine in a new bottle, the battery voltage / capacity is one big lie and so is the promised power output.

The receiver is still disappointing unless you live in the proverbial ‘middle of nowhere’. To make matters worse the GT-1 is more expensive than a Baofeng BF-666S / BF-777S / BF-888S.

In short: don’t buy one unless you’re a notorious masochist. Go for a UV-5R instead or, if you like/need this particular concept, buy the superior Anytone ANILE-8R.

 

Hans, PD0AC, is a regular contributor to AmateurRadio.com and writes from Almere, The Netherlands. Contact him at [email protected].

You may recall my blog describing the recent reception of the Oshawa Municipal Airport's NDB, "OO" on 391KHz. The Nav Canada beacon maintenance man, Alex, (VE3GOP) also a Yahoo Group NDBlist member was able to pay a visit to the beacon on Friday and confirm the reported output power is indeed just 7.5 watts! He even snapped a picture of the power meter ... talk about service!

courtesy: A. Wiecek, VE3GOP

Little "OO" has also been reported in Europe by none other than Roelof, PAØRDT, while using one of his own small active whips. I think this illustrates the remarkable propagation that can, and often does, take place below the broadcast band, even with a less than optimum antenna system ... good news for those planning a 630m backyard antenna installation!
Steve McDonald, VE7SL, is a regular contributor to AmateurRadio.com and writes from British Columbia, Canada. Contact him at [email protected].

• Thailand’s new master frequency list takes 6 meters back from ham radio
• UK regulator uses ham radio input in Ultra Wideband device rule making decision
• ITU symposium endorses small satellite regulation
• Successful transmissions of two new ham radio shows from Germany
• April 1st roving reporter is back with the latest on the FCC enforcement cutbacks

THIS WEEK'S NEWSCAST
Script
Audio