AmateurRadio.com

In my last post I described my QSO with VK2SSI while experimenting with portable antennas in my backyard. Well the reason I was testing portable configurations is because I needed work Cezar, VY0M, from Melville Island, IOTA NA-248, located in the Canadian arctic.  I knew that the scheduled expedition would occur during the week that I was at Philmont Scout Ranch in Cimarron, NM attending a training class and I would be sleeping in a tent for the week. New IOTA's are getting rare for me, with 1,050+ confirmed so I didn't want to miss this one.

I experimented with multiple antennas as I didn't know what I would be allowed to do at the camp. Would I be allowed to put up an antenna in camp? Would I have to find a remote location somewhere else? How long would my batteries last? So my plan was to try a Buddipole vertical first. It was relatively low profile and wouldn't attract a lot of attention. So I set up the station, in my tent, for a dry run.

As luck would have it, there was a 110v plug in my tent, the power intended to power a light and possibly a fan, so exit the batteries and in with the power supply. I set up the vertical and the antenna worked fine. I was using a Yaesu FT-857, which is a very capable radio, especially for portable use.  With 70 watts I worked into Europe with good reports, so I was thinking that I might just get by with this set-up. However, the first day that VY0M came up, he was on SSB. I never heard a peep from him and decided it was time for plan B.

After erecting the vertical, a few around camp inquired about it and everyone thought the radio set-up was cool, so the next afternoon I decided to put up the bright orange Jacktite, 30 ft.  collapsible pole with an end-fed long wire through a 9 to 1 balun. After I got everything connected, I turned on the radio and tuned the antenna with an LDG tuner. Everything looked good, so I checked the spots on my iPhone and Cezar had just moved to CW. I went to 14.040 and there he was with the fluttery signal common to stations in the far northern latitudes. After two or three calls I had him in the log, Victory dance. All the planning had paid off and I had another IOTA in the log.

What a blast ham radio is. Below is video of the set-up, right after I made the QSO. I didn't have the narrow CW filter on the FT-857, so the stations you hear are actually 1 KC up, but you can still hear Cezar's fluttery signal if you listen closely.



Mike Crownover, AD5A, is a regular contributor to AmateurRadio.com and writes from Texas, USA. Contact him at [email protected].

If you are like me, then you always want to know the loss of your coax at 6m,2m and 70cm, possibly higher I found this very useful table to compare various coax cables at different frequencies. You may have your own favorite table! If not, I hope you find this one useful.

See http://www.w4rp.com/ref/coax.html .

Roger Lapthorn, G3XBM, is a regular contributor to AmateurRadio.com and writes from Cambridge, England.

As I have said several times before, there is only one commercial rig that I fancy currently and that is the Yaesu FT991 that covers all of HF plus 6m, 2m and 70cm. However the UK price is still too high so I can wait and wait until the price drops. At £999 it will get serious consideration, but not at any higher price. The only other rig I fancy is an FT817 replacement, which may come later this year. Most of my operating is QRP and a 5-10W rig would suit my needs well.

Roger Lapthorn, G3XBM, is a regular contributor to AmateurRadio.com and writes from Cambridge, England.

Well, I have ordered one (yes I know I could have made one although not in my present state) so I hope this can be erected in the next few weeks, although I shall need help to do this as I am no good on ladders in my current poor state of health. It would be good if I could get a long wire erected at the same time for LF/MF use, although this could wait. At this time I am going for a single big-wheel rather than a stack.

I have decided against buying a 70cm big wheel at the same time as this would require a new length of low loss cable too. I also checked my existing low loss cable and this seems in good condition, so it will be reused. I may make my combined 2m/70cm antenna into a portable antenna when I have found out why the VSWR is poor.

See https://sites.google.com/site/g3xbmqrp3/antennas/bigwheel .

Roger Lapthorn, G3XBM, is a regular contributor to AmateurRadio.com and writes from Cambridge, England.

I've spent a couple of hours this weekend (so far mainly on Saturday), playing in the SKCC Sprintathon CW contest ... the rules demand that only hand keys, including bugs, be used. I hauled out my original gray Vibroplex, purchased back in 1964, when I decided that using a straight key was just too slow. I was doing a lot of DXing and contesting back then, with my trusty DX-20, VF-1 VFO and assorted groundplanes on top of my parents three-story house in the middle of Vancouver ... it's hard to believe that it was quiet enough there but those were the days before computers, switching power supplies and and so many other noise-making devices that we have today. They truly were the 'good old (quiet) days' of radio. My favorite contests back then were the 'W-VE', where any 'VE' became instant DX and the subject of good-sized pileups and the CW 'Sweepstakes' ... back when the exchange was, if I recall correctly, just NR, RST and QTH.

My antenna farm sat on our high, peaked roof and consisted of groundplanes for 40m, 20m and 15m ... these were made of inexpensive galvanized drain pipe, about three or four inches in diameter. The 40m one was guyed and also had one end of my 80m dipole attached to it, which ran out across the yard and across the back lane, terminating on one of BC Hydro's wooden (telephone) poles. Every once in a while the telephone guys would take it off and toss it over the fence whereupon I would get out the ladder and re-attach it, where it would stay for another year or so.

For this weekend's CW party, I have put my 'Tri-Tet-Ten' on 20m, doubling from a 40m crystal to 14051.5, placing me pretty close to the Sprint's watering-hole QRG of 14050. I have had way too much fun with this simple one-tube radio since building it, mainly for 10m CW, in anticipation of the present solar cycle's peak years. Although it puts out almost 5W when quadrupling to 10m, I can get a whopping 13W from it on 20m, which is plenty of power to have some fun.

So far I've worked about 40 stations, all on CQ's, since I can't really QSY to answer others ... so if you are around this afternoon, please give me a call should you hear my little rig. It's a real nice change to hear non-machine sent CW for a change and fists ranging from one end of the scale to the other ... really a nice reminder of what the bands used to sound like when I first got on the air.
Steve McDonald, VE7SL, is a regular contributor to AmateurRadio.com and writes from British Columbia, Canada. Contact him at [email protected].

The payload for the MADHEN Eggsplorer-1 High Altitude Balloon that I and the SKARS team launched in June has been located washed up on a beach in the Netherlands. Amazingly the egg was still intact inside the capsule.


On Friday evening I went to the Hucknall Rolls Royce ARC to give a presentation of HAB flights including details of the Eggsplorer-1 launch and its subsequent apparent loss at sea, then yesterday we had a trip to North Yorkshire and visited the Boon Hill Show and I admired the display of eggs within the produce tent.


It must have been synchronicity since a few hours later despite the poor mobile phone coverage I spotted a message on my mobile phone. It was from Jan Wouter Kramer from the Netherlands, whilst out on a remote beach in Terschelling he had found the Eggsplorer-1 washed up and taken some photographs!

Nearly six weeks to the day after launch she had been found with the egg apparently intact! I tried several times to ring back but the poor mobile coverage prevented it so sent a text message hoping it would reach him. I couldn't wait to get home to and finally did just before midnight.

I frantically logged on to check emails

Hey Andrew

Found your email on the site.
These are the pics we made.

We found it today about 14:00 during a walk on the beach of Terschelling in an area were not many people are walking because it's more than a two hours walk from the nearest houses.

As you can see the egg wasn't damaged but had probably lost it's strength. While trying to investigate what was inside the 'bulb' it broke open and the egg broke in two parts. It was nearly empty. Only a few cc of dark 'water' was left in it with a terrible smell .......

Best Regards !

Jan Wouter Kramer

The pictures were amazing






I emailed Jan back as far too late in the night to telephone

Hi Jan, 

Sorry I was able to take your call this afternoon but was out of coverage for most of the day.

Thank you very much for the information and pictures of the Eggsplorer-1. It was our first ever balloon flight and after it landed in the sea I thought we would never see it again.

Amazingly it appears very much intact, shame about the egg being rancid, would really have liked to get it back and would have paid for shipping - but I can imagine the smell was awful.

The Raspberry PI circuit board inside the box had a SD memory card which was held down with gaffa tape, I am not sure if it is still attached and it may have contained some photos of the flight taken with the onboard camera. However given the remoteness of the payload I understand if it is too far to return for such a slim chance.

Regards

Andrew Garratt (M0NRD)

As I wrote given the remoteness and the rancid condition of the egg I couldn't really expect Jan to go out again to collect it but had a fantastic text message this morning

Hi Andrew, thanks for your email. The good news is that I found the local police willing to pick up the remains of the eggsplorer. (They are allowed to drive on the beach by 4x4) I just got a phonecall that they found it and are willing to send it back to you.
So you have an address for me ??
Best regards
Jan Wouter

As you can imagine I am totally EGGSTATIC!!

I rang Jan this morning and had a great conversation, seems he visits here every year and goes beach-combing with his son, they have never found anything quite as exciting as this!


So MADHEN Eggsplorer-1 has traveled 31km into the stratosphere, landed in the sea and traveled approximately 370km from launch site to its final resting place on the beach. The World Egg Throwing Championship people are very eggcited.

Just hoping that there are some photos on the card if it has survived, cannot be sure from Jan's photographs. Since the flight I have suspected two possible fault scenarios, bad connector on the SD card on the Raspberry Pi or the antenna was broken off due to the backup tracker suspended underneath. I am hoping it was the latter and the card is recoverable and readable since it would contain pictures.

The backup tracker is also there but has lost its polystyrene egg cover, gps-antenna and battery pack but can see it is still attached to the main payload. The question is how long it has been on the beach? Given the relatively good condition of the box and the labels are still attached it may have been quite soon after splash down.

I am indebted to Jan for taking the trouble of contacting me and the police, I can't thank him enough! When I get the payload back I will post an update.

All the members of SKARS are eggcited and gives new impetus for the National Hamfest flight next month.
Andrew Garratt, MØNRD, is a regular contributor to AmateurRadio.com and writes from East Midlands, England. Contact him at [email protected].

The payload for the MADHEN Eggsplorer-1 High Altitude Balloon that I and the SKARS team launched in June has been located washed up on a beach in the Netherlands. Amazingly the egg was still intact inside the capsule.


On Friday evening I went to the Hucknall Rolls Royce ARC to give a presentation of HAB flights including details of the Eggsplorer-1 launch and its subsequent apparent loss at sea, then yesterday we had a trip to North Yorkshire and visited the Boon Hill Show and I admired the display of eggs within the produce tent.


It must have been synchronicity since a few hours later despite the poor mobile phone coverage I spotted a message on my mobile phone. It was from Jan Wouter Kramer from the Netherlands, whilst out on a remote beach in Terschelling he had found the Eggsplorer-1 washed up and taken some photographs!

Nearly six weeks to the day after launch she had been found with the egg apparently intact! I tried several times to ring back but the poor mobile coverage prevented it so sent a text message hoping it would reach him. I couldn't wait to get home to and finally did just before midnight.

I frantically logged on to check emails

Hey Andrew

Found your email on the site.
These are the pics we made.

We found it today about 14:00 during a walk on the beach of Terschelling in an area were not many people are walking because it's more than a two hours walk from the nearest houses.

As you can see the egg wasn't damaged but had probably lost it's strength. While trying to investigate what was inside the 'bulb' it broke open and the egg broke in two parts. It was nearly empty. Only a few cc of dark 'water' was left in it with a terrible smell .......

Best Regards !

Jan Wouter Kramer

The pictures were amazing






I emailed Jan back as far too late in the night to telephone

Hi Jan, 

Sorry I was able to take your call this afternoon but was out of coverage for most of the day.

Thank you very much for the information and pictures of the Eggsplorer-1. It was our first ever balloon flight and after it landed in the sea I thought we would never see it again.

Amazingly it appears very much intact, shame about the egg being rancid, would really have liked to get it back and would have paid for shipping - but I can imagine the smell was awful.

The Raspberry PI circuit board inside the box had a SD memory card which was held down with gaffa tape, I am not sure if it is still attached and it may have contained some photos of the flight taken with the onboard camera. However given the remoteness of the payload I understand if it is too far to return for such a slim chance.

Regards

Andrew Garratt (M0NRD)

As I wrote given the remoteness and the rancid condition of the egg I couldn't really expect Jan to go out again to collect it but had a fantastic text message this morning

Hi Andrew, thanks for your email. The good news is that I found the local police willing to pick up the remains of the eggsplorer. (They are allowed to drive on the beach by 4x4) I just got a phonecall that they found it and are willing to send it back to you.
So you have an address for me ??
Best regards
Jan Wouter

As you can imagine I am totally EGGSTATIC!!

I rang Jan this morning and had a great conversation, seems he visits here every year and goes beach-combing with his son, they have never found anything quite as exciting as this!


So MADHEN Eggsplorer-1 has traveled 31km into the stratosphere, landed in the sea and traveled approximately 370km from launch site to its final resting place on the beach. The World Egg Throwing Championship people are very eggcited.

Just hoping that there are some photos on the card if it has survived, cannot be sure from Jan's photographs. Since the flight I have suspected two possible fault scenarios, bad connector on the SD card on the Raspberry Pi or the antenna was broken off due to the backup tracker suspended underneath. I am hoping it was the latter and the card is recoverable and readable since it would contain pictures.

The backup tracker is also there but has lost its polystyrene egg cover, gps-antenna and battery pack but can see it is still attached to the main payload. The question is how long it has been on the beach? Given the relatively good condition of the box and the labels are still attached it may have been quite soon after splash down.

I am indebted to Jan for taking the trouble of contacting me and the police, I can't thank him enough! When I get the payload back I will post an update.

All the members of SKARS are eggcited and gives new impetus for the National Hamfest flight next month.
Andrew Garratt, MØNRD, is a regular contributor to AmateurRadio.com and writes from East Midlands, England. Contact him at [email protected].