AmateurRadio.com

As I mentioned in a previous post about my trip to the Aleutians, I am the owner of a new radio.  The reasons for the purchase were manifold, but driven by a fundamental shift in the way I view my operating (and living) philosophy.  I had long (at least 10 years) been collecting gear for a two- (or three-) tower contest station.  In this philosophy, the emphasis was on collecting antennas and towers as they became available on attractive terms.  It also meant keeping the inexpensive but well-performing pair of TS-930S HF transceivers for my SO2R setup and the FT-840 for my portable operations.  You can imagine from those past few sentences of description alone that this consumed a non-trivial amount of space and time.

Sarah began subtly hinting that “wouldn’t it be nice if we could clean up that pile of tower on the patio so we could have people over?”  My parents have been slowly migrating my junkbox from their place to ours.  It became increasingly clear to me that as long as we lived in this area it would be unlikely that I would put up the towers.  I started contemplating how to remedy this situation.  I identified a large collection of gear (including the Rohn 45 on the patio) that 1) could be replaced by a new radio, 2) I was not using, or 3) for which I simply did not have a plan.  So, I set out with the following theme to find a new rig:

Excellence in portable operation and competence at home.

I considered four radios:  Ten-Tec Eagle, Kenwood TS-590S, Elecraft K2/100, Elecraft K3/100.

I was strongly considering the K2/100 initially.  Its size and price seemed attractive.  However, when I did the math on what configuration I wanted, it basically ended up a draw with the Kenwood and the Ten-Tec with only a small bump more to the K3/100.  Plus, I’ve built enough kits to know that many of life’s most rewarding tasks tend to look better in the past than they do in the future.  Personal preference, of course!

The Kenwood TS-590S is acclaimed by a number of contesters as “the poor man’s K3.”  It has very similar features and performance numbers at a very attractive price.  I have always enjoyed Kenwoods as well.  But, the one thing that ultimately killed the TS-590S and the Ten-Tec Eagle was their lack of BCD band-data outputs.  The K3 also offered the 2-meter option, IF output (for panadapters), and very easy transverter interfacing.  It was really a no-brainer for me at that point since I had sold off enough gear to cover the cost entirely.

I bought the K3 kit and assembled it.  Anomalies notwithstanding, it amuses me greatly when people announce to the Elecraft e-mail list that “K3 #7777 is on the air”…it’s hard to keep from responding, “Congratulations on assembling your first LEGO kit.”  Unlike the K2, these “modular-kit” radios are very easy to assemble if you have a few hand tools and can follow basic directions.

My friend Oli, DJ9AO, informally asked me to compare the K3 to the TS-930S.  I’ve tested (subjectively) the K3 in a couple of demanding environments and I’m pleased to say that the K3 performed well, even with essentially “factory default” settings.

The K3 wins hands-down the strong-signal handling contest, even with the Inrad roofing filter in the TS-930S.  40 meters in ARRL Sweepstakes CW is a good test for this.  The FT-840 used to have severe mixing products (“beeps and bloops”).  These are not common with the TS-930S, but severe AGC pumping from nearby signals often covered up weaker signals.  Neither of these are problems with the K3.  In fact, the K3 is so good that you can tell just exactly who has key clicks because it’s possible to find two signals of otherwise identical strength on the S-meter and one will be inaudible within a few hundred Hz and the other will continue to bleed through and pump the AGC.  Well-done, Elecraft.

One thing that surprised me about the K3 was its apparently poor performance on the pileups from NA-039.  With the BW cranked down to 400 Hz, the filters rang like a bell in a pileup.  I have the 400-Hz 8-pole and 2.7-kHz 5-pole filters.  Widening the DSP bandwidth out to 700 Hz or so (which switches to the 2.7-kHz roofing filter) alleviated the problem with occasional AGC pumping from louder signals in the pileup.  In a post to the PVRC e-mail list recently, Frank, W3LPL, also confirmed that he prefers the 1-kHz 8-pole filter for CW operation.  Because I had the opportunity, I recently sprung for the special-order 700-Hz roofing filter.  It should arrive in March 2013.  I suspect there is considerable tailoring that could be done to the AGC system but I’m not there yet.  Once I realized that the bandwidth of 700 Hz was a sweet spot, the radio worked great in the pileups.  I have a feeling that I’ll also end up with the 1-kHz filter eventually.  But, I rarely open up beyond 700 Hz on CW so it will be interesting to see what is best.

A few other bright spots:

1. CW-to-Digital:  This is just plain cool.  Send with the built-in keyer and the radio modulates PSK31 or RTTY for you.  Decode it right on the screen.
2. Multifunction knobs:  The entire industrial design of the K3 is really unmatched in my opinion.  It has just the right number of knobs and menus.
3. Options:  They are plentiful and easy to install.  Keeps the initial cost low(er).

I’m extremely delighted with the K3 so far and my shack is getting more compact.  It’s also nice to have a radio with a built-in keyer for once…

Ethan Miller, K8GU, is a regular contributor to AmateurRadio.com and writes from Maryland, USA. Contact him at [email protected].

My “permanently installed” home HF station in my cursed covenant protected neighborhood employs a stealthy pine tree-mounted fan dipole to radiate nicely on 10m, 20m, and 40m.  But I’ve been missing out on a lot of fun on some of those other higher HF bands…  until recently.  I’ve found another way around the CCR Nazis with a temporarily erected portable ¼ wave vertical set up in my driveway.  I used it today to make contacts from Minnesota to Switzerland with 100 watts on 10m and 17m bands, but it works just as fantastically on 12m, 15m, and 20m bands.  Here’s the setup.

Radiating Element:  The radiating element I’m using is the MFJ-1979 stainless telescopic whip [~ $60].  It’s a pretty solid large extendable element that pulls out to 17 feet, so it’s effective down to 20m band without a tuner.  It collapses down to just 27 inches, so it can also be used for everything up to 50 MHz and it stows away nicely.  I tune it to a given band by simply extending or contracting it while measuring SWR with an analyzer, and I have marked the telescoping segments with permanent ink so I can zip quickly from one band extension to another without the analyzer hassle.  Yes, it’s a little extra trouble compared to using a true multiband antenna or a tuner, but I can usually obtain 1.2:1 SWR or better with only a few seconds of finagling.  Plus, I like to set up a station outdoors, either in the shade of the pines or just inside the garage within a few step of the well-stocked refrigerator, so it’s not too inconvenient to stroll over to the antenna to adjust it when I’m ready to switch bands.

Mounting Arrangement:  The telescopic element fits into a High Sierra Jaws Antenna Mount [~ $35 ].  This is a really nicely designed antenna mount with an adjustable clamp that’ll hold firmly onto almost anything.  It has a standard 3/8 – 24 thread female mount into which the MFJ-1979 fits and an SO-239 “UHF” connector on the opposite side.  It also has a convenient hole drilled into the clamp body on the electrical ground side through which a screw can be used to attach ground radials.  I like to have the Jaws clamp chomp down onto the wooden handle of a common dirt tamper.  The tamper has a heavy, flat metal base that is more than sufficient to support the fully extended vertical element, and the Jaws clamp works nicely with the wooden handle.  Plus it’s usually just hanging out in my garage and is conveniently portable.  A fat stake driven into the earth will do just as well with the Jaws clamp.

Ground Radials:  I constructed four bundles of ground radial wires, each bundle comprised of six wires soldered into a #10 ring terminal.  Each of the four bundles spreads out into a quadrant of radials under the telescopic element, 24 radials total.  The four ring terminals are stacked over the Jaws clamp hole and attached with a small stainless screw and nut.  Each radial wire is about 16 feet long.  I calculated the perimeter chord distance between evenly spaced radials for the 15 degree angle subtended between radials (about 49 inches), and I cut a stick to that length to make it easy to evenly space the radial wires when spreading them along the ground.  Since I store the wires in coiled bundles, I use a rock or a small tent stake to keep them held straight.

Set Up & Take Down:  It usually requires about 10 – 15 minutes to set up the entire antenna, with the bulk of that time dedicated to unfurling, spreading, and anchoring the ground radial wires.  I route about 40 feet of coax to the radio, typically outdoors as previously noted, or through a window to a comfortable operating location on cold days.  Antenna deconstruction is even quicker – kick the rocks aside, collect the quadrant ground radial bundles at the antenna and roll them up, securing each with a zip tie.  I leave them attached to the Jaws clamp ready to go for next time.  Scrunching up the telescopic element and detaching it from the clamp is a breeze, and it all tucks away in moments.

Results:  I’ve used this antenna several times in recent weeks at my home and with a portable station for Boy Scout Jamboree On The Air (JOTA), each time with fantastic results.  Today with nice F2 and sporadic E conditions I made many contacts into Europe and across North America with the 100 watts of a barefoot Yaesu FT-897D.  This simple antenna gets me onto those “other bands” that I’ve been missing out on, 12m, 15m, and 17m, as well as the familiar 10m and 20m bands that my fan dipole also delivers.  In particular, I have really come to enjoy 17m band’s more relaxed and gentlemanly character.  Maybe I’ll catch you there sometime soon!

This antenna can well serve the ham in a CCR protected neighborhood with a quick and easy temporary installation that won’t attract a lot of attention.  It also offers the convenience of portability, so it can be readily hauled to the local park, camp, forest or mountain location for relaxing outdoor operation.  Look for a feature article and video about this antenna set up coming soon to HamRadioSchool.com.

Stu Turner, WØSTU, is an author and professional educator who served as a US Air Force Academy engineering professor for eight years where he honed his skills of making difficult topics easy to understand. Contact him at [email protected].

Another day of good propagation allowed my love affair with 10m to continue.

Besides these contacts I heard, but couldn’t catch, stations in Mexico and Paraguay. I’m hoping the good propagation will continue so that I can add these to the log.

Because of this, not too much time was spent on WSPR today, so the WSPR map looked like this:

10m WSPR spots @ G4ILO 19 November 2012

Julian Moss, G4ILO, is a regular contributor to AmateurRadio.com and writes from Cumbria, England. Contact him at [email protected].

In my in-box the other day I received an email from QST regarding an app they were pushing. It's for ARRL members and for those who have an Ipad, Iphone and Ipod device. A short time ago QST announced the release of their digital QST. This gave you access to much more than just the paper monthly issue and you will notice in the paper issue there is online content that is mentioned in different write ups in the magazine. Now QST has an app were the digital QST can be accessed from your Apple device via an app. At this point I am able to go back 6 months and view other QST periodicals and all the digital goodies that go with it. 
Mike Weir, VE9KK, is a regular contributor to AmateurRadio.com and writes from New Brunswick, Canada. Contact him at [email protected].

A good day on 28MHz WSPR, particularly as I didn’t get started until I’d finished playing with the DSTAR kit this morning

Tim Kirby, G4VXE, is a regular contributor to AmateurRadio.com and writes from Oxfordshire, England. Contact him at [email protected].

Earlier in the week I noticed that there was a new version of the WinDV software that I use in conjunction with the DVAP, version 1.5.5. I downloaded it then but it wasn’t until this morning when I was doing some household chores and garden work that I had a chance to try it out. I hooked the DVAP up to REF001C and had a nice QSO with Brian, ZL1HN. During the QSO with Brian he mentioned getting a Raspberry Pi working with a DVAP which sounded an interesting project. Oh dear, I can see me getting a Pi at this rate…. I had another interesting chat with Clive 2W0CLJ who was doing good stuff with one of the DVRPTR boards and an FT7800.

Get the new version of WinDV at the dutch*star site

Tim Kirby, G4VXE, is a regular contributor to AmateurRadio.com and writes from Oxfordshire, England. Contact him at [email protected].

I nearly got myself locked out of the WSPR map page today. I must have managed to save the settings to try to display spots for all bands for the last 24 jours, or something like that, because whenever I went to the page the web browser froze up while it tried to render the map and I couln’t get back to the settings boxes to change it. I had to find out how to delete all cached files in Chrome before I could access it again.

10m WSPR spots @ G4ILO 18 November 2012

I lost quite a lot of time trying to sort that out. I also spent an hour or so seeing what I could work on 10m PSK31. I managed to QSO with several US stations including N7WET in Tucson, Arizona and KB5IAV in Baton Rouge, Louisiana.

I worked two all time new countries as well. Fabio CU3HN in the Azores has one of those QSLs that never fail to bring a smile to my face.

QSL of CU3HN

Victor, HP1AVS in Panama I had heard before but not managed to work. So I was pleased to add his call to the log as well.

QSL of HP1AVS

I love 10 metres!

Julian Moss, G4ILO, is a regular contributor to AmateurRadio.com and writes from Cumbria, England. Contact him at [email protected].