AmateurRadio.com

Listeners to the ICQ Podcast where I appear monthly as a Presenter probably heard me say that I was successfully treated for a highly aggressive prostate cancer (adenocarcinoma, Gleason 8) almost two years ago at the Mayo Clinic. While in Rochester for two weeks, I had a lot of time in bed recovering from the surgery before being released for home back in Mississippi. For me, I tried to keep my mind on things besides the cancer treatment as I had the top prostate cancer hospital in the U.S. treating me and the top robotic surgeon, Dr. Igor Frank, at the helm. So what does a ham think about in this circumstance? Let me tell you…

Antennas! I worked out plans for a half dozen portable antenna designs that had been smoldering in my brain before the unexpected diagnosis and biopsy. Don Field, Editor of Practical Wireless, expressed an interest in first dibs on each manuscript resulting from my experiments with portable HF antennas. Here are a few that are published or in-press as of this writing. And more to come.

Eiffeltenna

Based on the almost whimsical Youtube video by Jim Heath W6LG (now sk), I considered the photography lighting tripod, ubiquitous in the camera industry. Jim put together a quick-and-dirty (unusual for him) vertical antenna based on a type of tripod construction that electrically isolates the three legs from the telescoping vertical part. Brilliant! They are inexpensive so I bought a few from Amazon or eBay to experiment with. I paired the tripod with a 17′ telescoping whip and an inductor coil, finishing off the “fine French dining” concept with a tablecloth underneath of Faraday Cloth. Following my focus on making each section having a low resistance electrical connection when extended, it works very well. Very quick to set up, take down, and pack. It appeared in the October 2025 issue of PW. Bon appetit!

Delta Vee AutoLoop

Loop antennas of all designs have fascinated me since I was a teen building classic ones for AM BCB DXing. I have a sort-of horizontal loop around the edges of my roof due to HOA restrictions. )I have also written about that in PW-see March 2023 issue.) When Chameleon released their Tactical Delta Loop, I took a look at my friend, Steve KM9G’s take on it (see Temporarily Offline on Youtube). He found it was very flat across most HF bands. Hmm. Lawrence Cebik’s earlier models of loops, including the Delta geometry, showed that it has harmonics based on the design band and that height above ground places a significant part in the feedpoint impedance. What antenna magic have the Chameleon engineers come up with? Whatever it was, it priced out at over $400 USD.

From watching TO’s channel and the brief review of Michael KB9VBR, it appears that they use a fixed 5:1 balun to get the impedance down to the 50 ohm ballpark. I don’t understand TO’s flat SWR but antennas nearly on the ground can do funny things. So my take on the problem here was we can choose to optimize the balun wind for a certain band with some higher band harmonics working against a tuner for a reasonable match or just have a single band antenna. But wait. Why not use an ATU at the feedpoint to optimize the match across most HF bands? This only becomes practical with a light-weight battery-powered, RF-sensing ATU mounted directly at the “bare wires” from the loop’s geometry. That’s what I did here to create what I call the Delta Vee AutoLoop. I use a $40 used surveyor’s tripod without the head made by Manfrotto. It was purchased at a local electronic recycling center but I bought another on eBay for the same price. The head is what surveyors want so one without it is far cheaper. It has a standard bolt that I connect to an adaptor for the mount point as explained in the PW article.

Randy K7AGE says he’s building one to use on his parked truck when out doing POTA or other portable operations. This antenna appeared in the January 2026 issue of Practical Wireless.

Random Copper Stick

I had been puzzling over these carbon fiber masts since they came out. My friend George KJ6VU cautioned to me that they wouldn’t load up and they played havoc with his Packtenna wire antennas if they come in contact with them. So, bah humbug! Then I ran across Ben VE6SFX’s Youtube video on an experiment with on using Faraday tape on the outside of the carbon fiber mast. He said it worked as a random wire type of antenna! So, after working my brain for months on an angle for this, Ben’s experiment gave me a direction.

The Random Copper Stick was built by using a carbon fiber telescoping mast and copper tape—both 1 inch and 1/8″ widths—applied from the bottom to the top for each section of the disassembled mast. The very top section was removed as it was way too small to hold the tape. This gave me a reasonable length for a random wire antenna. My experimental measurements with a 17′ wire (20 meter measurement) showed a fairly clear phenomenon that Ben didn’t get into in his Youtube video. As shown below in a slide from a talk that I give to clubs on these experimental antennas, the carbon fibers disturb the relationship between the physical and electrical lengths of the wire as they are closely connected to the mast. (Score one for George KJ6VU’s observations!) Thus, using a 9:1 Unun with the mast works very well with an ATU at the transceiver. To quote my lawyer friend, Mike N5DU, I was shocked and amazed at how an antenna that I was convinced would not work turned out so well.

If you fancy taking a walking stick to operate portably, consider the RCS. It’s very easy to build, back and put up. I built one for my friend Scott K0MD to take with him on his trips to pair with his Icom 705. My article on the Random Copper Stick appears in the February 2026 issue of Practical Wireless.

Wave Caster Vertical

It is scheduled to appear in the April issue of PW but that should coincide with Spring Break weather at the beach. You can build the Wave Caster to Hang Ten while working some HF bands, lol. This one is also very easy to setup if you have anything in the portable site environment to clamp the mount. in the Wave Caster, I use an idea that Chuck KK6USY published on his Youtube channel in a coujple of videos. Particularly, he solved the problem of winding an antenna wire around a spool without it getting too much stress and eventually breaking. Chuck used a small resin reel with a ring terminal to solve this problem. Well, that solved a problem I wrestled with on ways to multiply antenna designs using these inexpensive carbon fiber masts with wire that wouldn’t take much time for the portable operators. (Not all have a half day to go to a POTA site that can be far, far away with a lengthy setup.)

With a Super-C photography clamp, almost any sturdy surface can be used to “brace” the vertical so it stays up while the temporary operation plays out. Just don’t forget it when you leave because I can tell you it is easy to do! This one is scheduled as of this writing to appear in the April issue of Practical Wireless magazine.

I have a couple of other designs that I am finalizing as the wild weather in the South permits. They may appear in PW but I’ll post a notice here if they do.

My time at Mayo Clinic was well spent. I cannot overstate how positive the medical treatment there was. Mayo treats 26,000 prostate cancer patients per year and have been rated #1 for many years. There was never a moment where I felt like I was a number on a lengthy list. I was fortunate to get connected with Dr. Igor Frank there as the “top gun” on robotic prostate cancer removal. I gave him a small momento as an expression of my appreciation as I was discharged. I understand that it may have made an appearance at the Department Christmas Party.