Drake 2NT And The Novice Rig Roundup (NRR)


One of this summer's radio workbench projects was to refurbish my Drake 2NT transmitter for this winter's NRR event. The 2NT was introduced in 1966 with the 'novice' ticket-holder in mind, selling for $129. It was the first and only CW-only transmitter produced by R.L. Drake.


As novice transmitters go, the 2NT was a cut above some of the others out there, boasting interesting features such as a built-in antenna changeover relay, sidetone oscillator, grid-block keying and built-in low pass filter.


The tune-up procedure was simplified as well and with Drake's reputation for quality construction, the 2NT became a popular choice for Novices and Generals alike.





My own 2NT was purchased, along with the matching 2C receiver and speaker/Q-multiplier combo over 25 years ago at a Washington state ham fleamarket. Ever since then they have been patiently sitting on the shelf, trying to catch my attention.

The motivation and much-deserved attention finally arrived this year after enjoying last winter's NRR and hearing several great-sounding 2NT's on 80, 40 and 15m CW. I operated the week-long Roundup with my homebrew 'Longfeller' at 5W output, in order to qualify for the QRP category.

6AG7 - 6V6 'Longfeller'
I have to admit, the Novice Rig Roundup, was one of the most enjoyable contests I have entered in many years! Hearing many rigs from the 50's and 60's sounding so good was just a bonus. It was particularly gratifying to be able to work the midweek daytime activity on 15m ... a luxury that we may not enjoy now for several years if most of the long term solar forecasts are correct.

I eventually ended up with 68 contacts, but at 5W, it was a challenge ... most of my many 'CQ NRR' offerings were unanswered, so it was mostly a 'search and pounce' operation. With this in mind, I soon decided that next time, I'll get the 2NT ready to go and hopefully, with a little more oomph, can attract some callers.

Each entrant received an NRR certificate - a nice touch

Rather than hunt down and purchase the individual replacement electrolytics, especially the multi-unit can capacitor which was impossible to source, I ordered the '2NT re-cap kit' from Hayseed Electronics. They supply replacement kits for several boatanchors and are able to make and stuff multi-section can capacitors to match the original size and specs ... and all at affordable prices.

After cleaning the chassis and all of the switches, re-tubing with new tubes and removing / replacing all of the electrolytics, the 2NT was ready to go. Using a crystal for excitation, the following results were obtained:

         80m 103W input 75W output efficiency = 73%
          40m  92W input 65W output efficiency = 71%
          20m  92W input 65W output efficiency = 71%
          15m  92W input 55W output efficiency = 58%
          10m  92W input 50W output efficiency = 54%

Keydown voltages averaged ~520V while plate current ranged from 170-200ma. All-in-all, right on target and not bad for a 51 year old transmitter!

The 6EA8 modified Pierce oscillator in the 2NT seems particularly 'crystal-friendly', as every old style FT-243 style crystal that I tried sounded great. Even the newer ones from AF4K using a modern HC-49 crystal slab mounted inside a vintage FT-243 holder sounded great and worked perfectly.

My newly refurbished 2NT - ready to go

A couple of days later, I returned to the bench to take some blog photos of the rig delivering power into the wattmeter. When I turned the 'stby' switch to 'transmit', the plate current suddenly shot up (with no keying) and the meter on my Variac supply indicated over an amp being drawn by the power transformer ... all with zero output and no crystal plugged-in!

A look at the schematic diagram revealed that with the grid-block keying system, the final amplifier's cathode is always grounded and a low voltage negative bias applied to the grid keeps the plate current cut-off until being keyed ... with cut-off bias missing, plate current will soar, along with transformer primary current. I suspected that something had gone haywire with the bias supply.


A quick check of the 2NT's printed circuit board containing the bias system components among others, indicated a discolored silicon rectifier (D5) in the bias supply. An in-circuit measurement revealed that it was indeed shorted, basically supplying raw AC across the filter capacitor and shorting out the transformer winding, quickly elevating the transformer's temperature in the bargain ... not good.

Although the diode only has to handle a small amount of current, it was mounted with a heat-producing 2W resistor straddling its top surface. As well, the phenolic circuit board was noticeably discoloured from the heat. I suspect this was the main reason that D5 eventually failed.

My 2NT was an early one, serial #670, so perhaps this parts-arrangement was re-engineered in later models. Once the diode was replaced with a much smaller modern one, of twice the rating, everything returned to normal. The last thing I would want to do at this stage is to burn out the transmitter's unique power transformer, undoubtedly impossible to replace nowadays.

The next bench project will be to refurbish and improve the stability of my Heathkit VF-1 VFO and to mate it with the 2NT.

'55 QST VF-1 ad
There are several things that can be done to a stock VF-1 to improve its performance. Its wonderful backlit green dial will bring back a lot of memories from my teenage operating days with the VF-1 ... most, but not all of them, warm and fuzzy.



Another small quirk noticed on my 2NT is the meter mount. My early model has the meter mounted so low that the silk-screened 'PLATE CURRENT MA.' label is not clearly visible when looking straight-on.

My #670
Later models show that this was changed by moving the meter a little higher so that the label can be easily seen without having to look down inside. Nothing major, but something apparently missed during the initial panel design.

Later models
I'll have more to say about the 2018 NRR later, but if it's something that you may be interested in trying and you don't yet have a suitable novice-style rig, it's not too late to start looking, building or refurbishing.

You can read many interesting soapbox comments and see some nice NRR station photos from the previous two events here and here, but read with caution as you could easily get hooked. I find pages like this very inspiring and they remind me of the days when QST would publish photos, soapbox comments and exacting equipment descriptions used by each section winner in the annual November Sweepstakes contest.

Winner's gear in '55 CW SS - remember these?
NRR activity really skyrocketed last winter and I expect that it will be an even busier event next time. There are several CW contests that I'm looking forward to this winter and the NRR is right near the top of the list. I hope to see many of you in the 2018 NRR!
Steve McDonald, VE7SL, is a regular contributor to AmateurRadio.com and writes from British Columbia, Canada. Contact him at [email protected].

One Response to “Drake 2NT And The Novice Rig Roundup (NRR)”

  • David WB4ONA:

    FWIW according to the U.S. Government’s Bureau of Labor Statistics Consumer Price Index Inflation Calculator, $129.00 in 1966 is worth $995.97 51 years later in 2017. Remember, to that price you need to add the price of a receiver and (hopefully) a transmit VFO.

    In 1967 the Heathkit HW-16 transceiver appeared. At around $110 (plus around $35 for the optional matching HG-10/10B VFO) the HW-16 was far more attractive for many Novices. The HW-16 was a 90W capable CW only transceiver kit that covered the lower 250KHz of the 80m, 40m, and 15m bands.

Leave a Comment

Subscribe FREE to AmateurRadio.com's
Amateur Radio Newsletter
News, Opinion, Giveaways & More!

E-mail 
Join over 7,000 subscribers!
We never share your e-mail address.



Also available via RSS feed, Twitter, and Facebook.


Subscribe FREE to AmateurRadio.com's
Amateur Radio Newsletter

 
We never share your e-mail address.


Do you like to write?
Interesting project to share?
Helpful tips and ideas for other hams?

Submit an article and we will review it for publication on AmateurRadio.com!

Have a ham radio product or service?
Consider advertising on our site.

Are you a reporter covering ham radio?
Find ham radio experts for your story.

How to Set Up a Ham Radio Blog
Get started in less than 15 minutes!


  • Matt W1MST, Managing Editor




Sign up for our free
Amateur Radio Newsletter

Enter your e-mail address: