Remembering The ‘Woodpecker’



Early last week, Paul (K7CW) sent me a link to an interesting video showing the Duga antenna system. The term was not familiar to me but when I went to the site I immediately recalled the significance of what I was seeing!



Those of you that have been hams for a long time will no doubt recall the Russian 'Woodpecker'. The 'Woodpecker' was a strong, fast repeating signal / racket that often wiped out amateur communications on 20m here in North America ... maybe other parts of the world as well.

Amateurs with yagis eventually determined that the signals (yes there was more than one it seemed) were coming from the USSR. The QRM was persistent and in spite of formal complaints being lodged via diplomatic channels, continued for many years ... from 1978- 1989. Some of the new transceivers built during the time actually had a 'WOODPECKER' position on the noise blanker switch, hopefully offering some relief to the problem.

For you younger folks, here's what Duga usually sounded like:


Several web searches brought up numerous descriptions of the Duga (Russian for 'arc' or 'bow') project, some with conflicting information. From what I can sort out, there were three Duga sites ... one near Chernobyl, another near Chernihiv and a third, much later, in Siberia. The first two (Duga and Duga-1) were in the Soviet Ukrainian SSR (now Ukraine) while the third was located near Komsolmosk-on-Amur in the Russian far east. One source indicates that the second Chernobyl site is often misidentified as the Duga-3 array and should be referred to as Duga-1, with Duga-2 being the Siberian location.

Initial speculation suggested this intrusive signal was some form of 'jammer' ... very common during the Cold War. It wasn't long before the true nature of Duga was thought more likely to be an 'over-the-horizon' (OTH) long-range radar system for detecting the launch of North American missiles aimed at the USSR. The three radar sites gave the Soviets good over-the-pole coverage as well as to the east, where it could also be utilized for tracking domestic rocket launches.

courtesy: http://www.globalsecurity.org/wmd/world/russia/steel-yard.htm

The antennas themselves appear to be phased dipole curtain arrays, commonly used in various configurations by shortwave HF broadcasters.

courtesy: http://www.antenna.be/hr.html
These antennas featured an array of phased dipoles in front of a screen curtain 'reflector', often made of rows of wide-spaced wires. One source indicates that the Duga arrays developed ~30db gain over a standard half-wave dipole ... an enormous task on these HF frequencies. One system had a '4/4/1' configuration meaning each bay consisted of a dipole array 4 wide and 4 high. Another source spoke of  a system that was 32 high and 16 wide in total. Whatever the numbers, these free-standing structures were gigantic and true marvels of engineering. The large Chernobyl array is 150m high and 500m wide, with an estimated weight of ~ 14,000 tons.

Each site was paired with a receiving array ... remember, this was a radar system, with two of the three systems having the receiving array located tens of kilometers from the transmitter. The Chernobyl Duga is said to have had the receiving antenna located on site. Sources discussing physical size indicate the dimensions for the receiving array to be larger than those of the transmitting antenna. It seems possible then, that the pictures and videos commonly found are those of the receiving array and not of the transmitting antenna. It might make sense to have more gain on 'receive' than on 'transmit' as echoes from small targets many thousands of miles away would not be easy to detect. No matter what the actual case, I can only imagine the fun of hooking up an HF transceiver to one of these arrays during a DX contest on 20m CW!

The Chernobyl site shows two arrays, side-by-side ... possibly the larger being that used for receiving and the smaller one for transmitting. This antenna has been noted as a 30/10/2 array ... 2 bays, 30 dipoles wide and 10 high, 600 elements in all!

Further research tends to indicate that each dipole is what is called a 'Nadanenko' dipole. The main feature of this style was its cage-styled construction, giving the element a large diameter resulting in a broad bandwidth.

courtesy: https://shema.info/en/antenna/
Each dipole was fed at the center with open-wire ladder line and some pictures show obvious signs of open wire phasing lines, no doubt used to electrically steer the array over its reported 30 degree directional pattern.

courtesy: englishrussia.com
After watching the video, Paul (K7CW) made some interesting observations, some of which may be seen in the above photograph. His eyes must also be a lot better than mine as he managed to correctly count the number of dipoles in the array!

First, you see that there are two sets of arrays 15 driven elements wide by 10 driven elements high for a total of 600 elements! They are intermeshed and offset from each other by 1/2 wavelength both vertically and horizontally. There is a horizontal wire screen reflector behind the driven elements.

Some of the other things I noticed are ...

... you can see the open-wire feeds and reflector screen. Each set of collinear elements is fed individually with open wire line. There is a support line between each two bays of driven elements.

... that the reflector screen is supported on the sides by the stand-alone free-standing towers at each side of the array. (I had been wondering why they would have those towers next to the array like that. Now I know.)

... that the element supports are steel pipe instead of fiberglass (or something similar). Apparently, the shape of the radiators allows for the pipe supports to enter the element cages at the element low-impedance point which made the supports invisible to the antenna and also allowed for the supports to not radiate themselves.

courtesy: http://anzee.livejournal.com/65530.html
There are a number of YouTube videos showing various adventure-seekers climbing the Duga array near Chernobyl. The videos give you a better idea of its sheer mass as well as a closer look at the dipole structures themselves.



The Duga system was operative between 7 and 19MHz, with 40kHz wide pulses, usually lasting for about seven minutes. The most common pulse rate was at ~10Hz but this sometimes varied. Power levels used often mention 10 megawatts but it's not clear if this was RF output, peak pulse power or ERP.

It's somewhat gratifying after all these years, to actually see close-up, where the Woodpecker signal started its journey around the world and to appreciate the superb engineering that went into these impressive structures ... but sad to see the last one in such a rusted state of decay and abandonment. It would be nice to hear it just one more time ... but please, only for a couple of minutes.
Steve McDonald, VE7SL, is a regular contributor to AmateurRadio.com and writes from British Columbia, Canada. Contact him at [email protected].

7 Responses to “Remembering The ‘Woodpecker’”

  • Bob KK5R:

    I have also studied the waveform while working in an electronic test lab. There was some indication that the leading edge of pulses were also Frequency Modulated at a very slow baud rate for text information, no doubt encoded. Either that or the transmitting signal was “trashy” and this was a natural characteristic of the waveform. Keep in mind the probably megawatt level signal driving that array. And the signal was very widespread, being heard when nothing else was heard. Also, the signal jumped around. When it disappeared on one frequency, it reappeared instantaneously some 100 KHz away, possibly in an attempt to keep anyone from actually studying the signal or to keep down the number of complaints. Who knows what passed in those red devil’s minds. {;->

  • n8gcp:

    we old timers have known abt that for years. also there is 1 in alaska.

  • Mitch NØDIM:

    Any chance one of these was used as the “wall” in the movie Divergent?

  • Steve VE7SL:

    Looks like it Mitch, along with some creative computer work to put it on a big cement foundation and extend it forever.

  • Goody K3NG:

    Good article.

  • John WB7NWP:

    I certainly remember hearing the Woodpecker.

    I also remember that, by complete coincidence (I’m sure) hams would tune up their transmitters on frequencies that were being used by the woodpecker, and often send “dots” with automatic keyers at the same rep rate as the Woodpecker (about 5 Hz). These “accidental” transmissions were pretty much guaranteed to jam the Woodpecker transmitters, as the transmissions were far stronger than any echoes that the Soviets hoped to find.

  • JP Cardot KA5DCZ:

    From : John WB7NWP
    I also remember that, by complete coincidence (I’m sure) hams would tune up their transmitters on frequencies that were being used by the woodpecker

    From: KA5DCZ , 06-08-2023
    In 1980, I too, COINCIDENTLY, tuned and transmitted on the frequency of the “woodpecker”, doing exactly what John WB7NWP described. I will never know if my attempts to defeat the purpose of the Russian OTH were successful, but I hope that I was “bugging the hell out of their system”. Five seconds of transmit then listen If the “woodpecker” was still present , re-transmission . If the “woodpecker” had disappeared, Iwas hunting “him” again and repeated my transmissions… over and over.
    Was it LEGAL ? The Russians did not seem to care, invading OUR frequencies… SO?

    If many HAMS had done the same, we would have defeated a multi-million dollars OTH with our “cheap” equipment .

    note: I am still in the “call registery book” but I am no longer “radioactive”.

Leave a Comment

Subscribe FREE to AmateurRadio.com's
Amateur Radio Newsletter
News, Opinion, Giveaways & More!

E-mail 
Join over 7,000 subscribers!
We never share your e-mail address.



Also available via RSS feed, Twitter, and Facebook.


Subscribe FREE to AmateurRadio.com's
Amateur Radio Newsletter

 
We never share your e-mail address.


Do you like to write?
Interesting project to share?
Helpful tips and ideas for other hams?

Submit an article and we will review it for publication on AmateurRadio.com!

Have a ham radio product or service?
Consider advertising on our site.

Are you a reporter covering ham radio?
Find ham radio experts for your story.

How to Set Up a Ham Radio Blog
Get started in less than 15 minutes!


  • Matt W1MST, Managing Editor




Sign up for our free
Amateur Radio Newsletter

Enter your e-mail address: